93 blazer 4.3 vortex injector probs

[slp4days]

Ok thx a lot I won't be able to get to it today but ill get to it soon thx a lot for all your help

[MT-2500]

Originally Posted by slp4days

Ok thx a lot I won't be able to get to it today but ill get to it soon thx a lot for all your help

You are welcome.
Let us know how it goes.

[slp4days]

I pulled each poppet and checked them 1 at a time and all 6 was squirting gas when I cranked it over the fuel pressure was 60 psi turning the key on and around 63 psi cranking it over but it fired like it wanted to start which it did that now and again before so I'm not sure if it would start or not an even if it did run and start I'd be worried not noing what exactly got it to work any suggestions I'm not sure whet to do next thx for your help and time

[MT-2500]

Originally Posted by slp4days

I pulled each poppet and checked them 1 at a time and all 6 was squirting gas when I cranked it over the fuel pressure was 60 psi turning the key on and around 63 psi cranking it over but it fired like it wanted to start which it did that now and again before so I'm not sure if it would start or not an even if it did run and start I'd be worried not noing what exactly got it to work any suggestions I'm not sure whet to do next thx for your help and time

If all else fails put it back together and see if it will start .

[slp4days]

Yep ill do that ill get plenum gasket this weekend an see how it goes thx for ur help an time ill let u no how it goes

[slp4days]

I got her all back together and its starting and running I don't like knowing why it stopped running but I'm glad its going again. Thx for all your help if it happens again ill no what to test and what to test for now.

[MT-2500]

Originally Posted by slp4days

I got her all back together and its starting and running I don't like knowing why it stopped running but I'm glad its going again. Thx for all your help if it happens again ill no what to test and what to test for now.

You are welcome.
Remember if it does it again proper testing.
I have had the injector wiring harness inside plamtum do things like that.
Good Luck

[slp4days]

I'm pretty sure the prob I had is a bad injector connector I'm putting a new connector on an I don't think ill have anymore probs w it if I do ill post and let u no thx for your help

[MT-2500]

Originally Posted by slp4days

I'm pretty sure the prob I had is a bad injector connector I'm putting a new connector on an I don't think ill have anymore probs w it if I do ill post and let u no thx for your help

You are welcome. Glad to help.
Yes connector or wiring give a lot of problems.
Good luck
And let us know how it goes.

[slp4days]

I tried 2 get a new injector connecter I got 1 for a 4.3 cpi whitch is wat I have and it was the wrong 1 so I got 1 4 a 4.3 tbi and I think that will work but I pulled alittle more wire thru the motar so the plug setup alittle better and so far so good if it starts cutting out again ill put the connector on for the tbi injector thx again for all your help

[MT-2500]

Originally Posted by slp4days

I tried 2 get a new injector connecter I got 1 for a 4.3 cpi whitch is wat I have and it was the wrong 1 so I got 1 4 a 4.3 tbi and I think that will work but I pulled alittle more wire thru the motar so the plug setup alittle better and so far so good if it starts cutting out again ill put the connector on for the tbi injector thx again for all your help

You are welcome.

And
Good Luck