-
Grand Future Air Dried Fresh Beef Dog Food
Air Dried Dog Food | Fresh Beef

Carnivore Diet for Dogs

Go Back   Automotive Forums Car Chat > Chevrolet > Venture
Register FAQ Community
Reply Show Printable Version Show Printable Version | Subscription Subscribe to this Thread
 
Thread Tools
  #1  
Old 01-18-2004, 03:28 PM
kirk1060 kirk1060 is offline
AF Newbie
 
Join Date: Jan 2004
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
Question 1,2 & 3 on blower switch not working

I have a 98 venture LS. The problem I'm having is the first three settings of the blower switch does't work. But when it's set to 4 or 5 it works fine. I was told the resistor was bad. If thats the case, can anyone tell me where its located and the best way to get to it.

Any help appreciated..

Last edited by kirk1060; 01-22-2004 at 12:42 AM.
Reply With Quote
  #2  
Old 01-27-2004, 02:19 PM
rodeo02 rodeo02 is offline
AF Enthusiast
 
Join Date: Mar 2003
Posts: 3,213
Thanks: 0
Thanked 4 Times in 4 Posts
This is the result of a bad resistor pack (device that regulates blower speeds). They are usually mounted somewhere near the switchgear or in the blower box/duct. When the resistor(s) burn out, you typically have only "off" and "high" settings.
G/luck
Joel
Reply With Quote
  #3  
Old 02-29-2004, 10:53 AM
DRW1000 DRW1000 is offline
AF Enthusiast
 
Join Date: Feb 2004
Posts: 1,422
Thanks: 0
Thanked 9 Times in 9 Posts
Re: blower control switch

Quote:
Originally Posted by rodeo02
This is the result of a bad resistor pack (device that regulates blower speeds). They are usually mounted somewhere near the switchgear or in the blower box/duct. When the resistor(s) burn out, you typically have only "off" and "high" settings.
G/luck
Joel
The resistor pack on the venture is located under the dashboard on the passenger's side. You have to take the following steps:

Disable the airbag
remove the decorative trim

The resistor pack is located near the firewall behind the blower motor. It is tricky to get to and an even trickier step is removing the wire harness from the blower motor since it is not visable. I would recommend having a look at a blower to see how it is connected first.
Anyway remove this connector and the harness to the resistor pack (about 8 wires). The resistor pack is held by three screws in a triangle formation. The one near the front needs to be removed. The two near the firewall only need to be losened and they are tricky to get to. Once this is done lower the front and slide it forward to release and you should have it.
Reply With Quote
  #4  
Old 06-19-2004, 04:27 PM
carl300 carl300 is offline
AF Newbie
 
Join Date: Jun 2004
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
resistor replace

just replaced my resistor pack on 98 venture. did not remove anything except the resistor pack. job took 25 minutes because of difficulty in working position. while you only have to loosen the back two screws they are very hard to get the socket on. use 1/4 drive with 7/32 socket and poss short ext. press hard against fire wall and you will get it on there. good luck
Reply With Quote
 
Similar Threads
Thread Thread Starter Forum Replies Last Post
2002 cavalier blower speed control switch problem sixwongs Non-Performance 3 02-14-2011 09:48 PM
A/C Control Dual Zone switch assembly Not Working bigpoppabear Intrigue 4 06-22-2010 12:28 PM
06 escape blower fan switch milo42gpw Escape | Maverick | Escape Hybrid 1 03-26-2009 07:38 PM
Heater/AC Blower Control Switch kidtau Caravan | Voyager 2 01-02-2009 02:18 PM
Smoke from Blower Control Switch 1997BlazerLT Blazer 3 03-03-2006 12:39 PM

Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums Car Chat > Chevrolet > Venture


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 09:10 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts