Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
08-22-2009, 08:12 PM | #1 | |
AF Newbie
Join Date: Aug 2009
Location: SimiValley, California
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
1991 Cressida will not start
I swaped engines on my 91 Cressida with the same engine only 40 to 60 thousand miles on it from Japan. The problem is it will not start. I get plenty of fuel and spark, but no injector signal or pulse. I have two computers and both get the same results. This is the second motor that I have swaped within the last four years. the first motor no problem it started first time. Any suggestions would be helpful.
|
|
08-23-2009, 10:48 AM | #2 | |
The RustBuster
Join Date: Feb 2006
Location: La Plata, Maryland
Posts: 2,290
Thanks: 1
Thanked 51 Times in 50 Posts
|
Re: 1991 Cressida will not start
Was the first swapped engine from Japan as well? If so, all I can think of is that the pin-outs from the sensor connectors to the ECM (presumed USA) are different in Japan. I'd start by tracing those back to the sensors to be sure they are correct for this USA application.
If however, you have swapped out all the US sensors onto the Jap block, then my guess is a sensor is in a different position and not reading correctly or one has failed during the swap. Or it could be the ignition coil. If it is a similar part to the Gen III Camry, they are notorious for failing while still providing a spark. Ayup, I'm grasping for straws, but hope this will help nudge to to a solution...good luck!
__________________
Current Garage: 2009 Honda CR-V EX 2006 Mazda 3i 2004 Chevrolet Silverado 2500HD 2003 GMC Envoy XL 2000 Honda ST1100 2000 Pontiac Sunfire Vehicle History: 2003 Pontiac Vibe AWD - 1999 Acura Integra GS - 2004 4.7L Dakota Quad Cab 4x4 - 1996 GMC Jimmy 4wd - 1995 Chevrolet C2500 - 1992 Toyota Camry LE 2.2L - 1992 Chevrolet S10 Ext. Cab 4.3L - 1995 Honda ST1100 - 1980 Yamaha XS400 - 1980 Mercury Bobcat. |
|
08-23-2009, 04:08 PM | #3 | |
AF Newbie
Thread starter
Join Date: Aug 2009
Location: SimiValley, California
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 1991 Cressida will not start
First motor was from Japan also.
|
|
08-25-2009, 10:42 PM | #4 | |
AF Newbie
Thread starter
Join Date: Aug 2009
Location: SimiValley, California
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: 1991 Cressida will not start
What would cause injectors not to pluse. On a 1991 toyota cressida?
|
|
08-26-2009, 12:02 AM | #5 | |
Resident Chemist
|
Re: 1991 Cressida will not start
Guesses:
If you are not getting sufficient air flow through the AFM, a sticky AFM, or a bad electrical connection which would prevent the AFM to not send a signal that makes the ECM think the engine is cranking, no injector signal. Have you checked for stored codes in the ECM? Ignition timing? Wiring connection? Power to ECU? Water temperature sensor? Air temperature sensor? Injection signal circuit wiring? Stuck injectors?
__________________
Forum Guidelines:http://www.automotiveforums.com/vbulletin/guidelines.html "What we've got here is a failure to communicate" |
|
|
POST REPLY TO THIS THREAD |
|
|