|
|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| JDM Motor & Parts info/chat Discussions on Mugen, Spoon etc. Plus, info on motor swaps (b18 's, b16's h22's etc) and other JDM info! |
![]() |
Show Printable Version |
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
|
|||
|
|||
|
Ok so i have a 93 Civic ex Single head VTEC and i was planing to chip my ECU i was looking at a Mugen chip and the VTEC engages At 5000 RPM and redlines at 9000 RPMs i was talking the the Shop that sell them and told me they can custom it to VTEC to engage at 5000 Rpm and redline at 8000 since 9000 it to much and i can blow my engine is he right
|
|
#2
|
||||
|
||||
|
Re: P28 Chipped ECU
what modifications do you have? If you only have an intake, exhaust, and a header; then it's worthless to get a chipped ecu. Even if you have more than that, you should get something a lot better than one of those cheap chips. All they do is advance the timing (not needed in most cases), and increase fuel to the engine. Adding more fuel will lower your gas mileage, and often create a too rich condition. Most people think that the more fuel you add the better, it's not the case at all. An engine like enough fuel to where it's slightly richer than lean.
|
|
#3
|
|||
|
|||
|
Re: P28 Chipped ECU
well the chip im getting is for Atmel they got all my set up and were going to adjust it to get more power out of it and by the way they said ATMEL is the most popular brand there is
|
|
#4
|
||||
|
||||
|
Re: P28 Chipped ECU
.....i'd be hesitant
__________________
2015 DGM STi - 2006 SGM STi - 1999 Built/boosted GSR |
|
#5
|
||||
|
||||
|
Re: P28 Chipped ECU
amtel is just the name of who makes the chip itself. Like how AMD makes their processor chips. amtel isn't the program they use to tune with. And I completely agree with Schister66. Who knows if they are really going to change the base "Mugen" programming specifically for your mods, or if they're just going to just use the base one. And it's not a real Mugen programming, it's a company that stole the Mugen programming and changed it to meet their needs. I've worked on quite a few cars that had chipped ECU's (and I'm not refering to chipped as in hondata or chrome, etc), and they've all had major problems. It's almost impossible to get them to run right.
|
|
#6
|
||||
|
||||
|
Re: P28 Chipped ECU
i'm going to say this once.....chipping your ECU is NOT a way to make power UNLESS you have enough supporting modifications that make the car far from stock.....the way you actually make power from "chipping" the ECU is by getting a tuned fuel/ignition map for your car specifically. When i boosted my GSR i had to have this done....it is to ensure that the car doesn't run lean or extremely rich.
You need a tuning software for one...you can use free stuff like Crome if you so desire. But i want to clarify this....you aren't going to see a significant gain from any of this without PROFESSIONAL DYNO TUNING. I paid $375 to get my GSR tuned....unless you're willing to spend nearly $400 to make a measley 4whp, i wouldnt do it
__________________
2015 DGM STi - 2006 SGM STi - 1999 Built/boosted GSR |
|
#7
|
|||
|
|||
|
Re: P28 Chipped ECU
any shop that tries to sell you a chipped ecu and all he does is change the vtec engaement and changes the redline for you without telling you that doing that without being on a dyno is full of shit. reasons why:
1) if he knows its pointless, its not worth trusting him because all he wants to do is make a sale instead of leaning you the right way. or 2) he doesnt know anything about chipped ecus and engine management systems.
__________________
99 [email protected] psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me. |
|
![]() |
POST REPLY TO THIS THREAD |
![]() |
|
|