sound deadning

[Chuki_breath]

well ill let you all know before hand.......DOING THAT IS A PAIN IN THE ASS!!!!!! But yea it does take off some weight. I filled up a 5 gallon bucket witht the shit and there's still more fragments all over the place. Need a shop-vac to suck all that crap up. So messy. Its so tedious. I did the dry ice method. It does work. You can do it without, but the dry ice seemed to have frozen it up to allow bigger sheets to peel off rather than kind of "chip" off. I ran out of dry ice and had to do half the back without. Its hard sitting in a trunk and trying to find room to swing and chizzel. Its not really that hard of a task, you just get sore and tired of chizzeling for hours. And your knees hurt from squating for so damn long. And your ass hurts because there's no cushion to sit on lol. I know im gonna have a sore back and right arm tomorrow.......alright im done bitching.

But it does clean the ride up a bit. But you will hear EVERYTHING when driving.....little rocks and shit. I would say listen to rally cars.....thats how it will sound.

also dry ice is fun. I put a few chunks in a water bottle, threw it in the lawn. I would say it blew the water bottle about 30ft down the road lololololol. It was awesome as hell. I didnt know what to expect. I knew it would blow up....but not like that. yea i did it a couple more times. Through one in my pond.....made a mushroom cloud of water whahahahhahahahaha. That shit is pretty cool stuff. Its so cold you can hear it pop and squeek. Put it on warm metal it starts to sizzle and move by itself. Its -109 degrees. So you can touch it for like 2 seconds and your skin will hurt and turn white.

[S13Driftfiend]

lol nice... hows the interior look with all of that shit taken out? im saving that project for a long boring day i have nothing else to do lol

[nissan_240sx]

that shit sucks.. I remember helping my friend with that awhile back lol

[Chuki_breath]

i think it looks alot better. Its just the metal look. You definantly need to paint it though if you plan on leaving all the interior/carpet out. The factory just paints over the stuff so when you peel it up, it leaves big unpainted spots. I mean you dont absolutely have to, but it would look alot better. You may have to sand the excess material that sticks to the metal still. It chips off, but leaves little little patches here and there. Some parts have caulk on them too so you have to get rid of that too. The car looks bad ass with nothing in it. Just wirelooms hanging everywhere. Thats what i have to do next.......rip all the looms out that i dont need. Ill get a pic of it soon.

[S13Driftfiend]

post pics we cant get enough of this car lol

[MetalHeadZaid]

LOL at you and dry ice. you're not suposed to touch it!

[nissan_240sx]

^
if only someone told me that when I was 13.. lol

[S13Driftfiend]

do you guys have frostbitten hands now lol

[Chuki_breath]

lol yea you can touch it for like 1-2 seconds. I used an oven mit....

[S13Driftfiend]

hey i dunno if you have access to an air chisel, but i guess using that and acetone works pretty good too. even though its too late lol

[usar89b]

An air chisel can be had for 20 buck at Lowe's, but you need an air compressor to run it!

[MetalHeadZaid]

how much to compressors go for? those are handy for everything

[nissan_240sx]

500 + and up probably?
you don't want a small tank that will recharge itself every min, very annoying imo lol

[240SXSlideStar]

We sell them around 250-350 for a rly good one on sale.

[MetalHeadZaid]

they look pretty usefull, il probably get one some time in the future.