|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| Let's get Technical! Discussion for hardcore in-depth motor heads! |
 |
 Show Printable Version | 
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
03-10-2006, 01:36 PM
|
||||
|
||||
|
Skunk2 manifold for turbo?
This might be a funny question but I don't know a whole lot on boosted car's since I haven't owned one yet. Well here it is. Will a Skunk2 intake manifold for a 95' GSR work well if I decide to go turbo later on? Or should I just wait and buy one specifically for turbo. I really can't wait to get rid of my old manifold but I don't want to waste money if I'm just going to have to buy a different one in the near future. And if there is one for a turbo application which one should I buy and will it be ok to use it now until I do boost my ride? Comments, suggestions? Thanks.
__________________
JDM B18C, LSD tranny, Exedy flywheel/clutch, AEM intake, Greddy cat back, stainless header, Skunk2 manifold, Koyo radiator, Tokico Illumina full coilovers, black 17" Konig Hurry's, dc strut bars, custom cf hood, poly motor mounts, alum. battery bracket, b&m short shifter, Viper alarm, spoon chip, Tenzo R seats, Kenwood amp, Pioneer and MTX speakers w/cross over's, euro antenna, NGK wire's and plugs, Mobil 1 syn. and a whole lot of attitude. 9.4 sec 1/8 mile at Irwindale 4/20/06 
|
|
#2
03-10-2006, 02:16 PM
|
||||
|
||||
|
Re: Skunk2 manifold for turbo?
There aren't IM's specifically for turbo or all motor, they are the same. You'll probably lose some power by switching it over before going turbo though.
|
|
#3
03-10-2006, 07:21 PM
|
|||
|
|||
|
Re: Skunk2 manifold for turbo?
dyno results on skunks are disappointing.
proven manifolds are" edlebrock, golden eagle, AIR and AEBs just to name a few.
__________________
99 [email protected] psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me.
|
|
#4
04-14-2006, 08:32 PM
|
|||
|
|||
|
Re: Skunk2 manifold for turbo?
i dont think it will so bad to get a IM before ..because ive seen so many dynos for the Blox IM and the average is about 7-8 whp on a b18c1 ..the skunk2 manifold is just like the blox i guess and i have a blox IM it feels great ..
|
|
#5
04-15-2006, 03:37 AM
|
|||
|
|||
|
Re: Skunk2 manifold for turbo?
we are talking about boost here. not na.
__________________
99 [email protected] psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me.
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
