|
|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Beef Dog Food | IgorSushko.com | Corporate |
|
#1
|
|||
|
|||
|
Ok first off dont send me hate mail over the name.I own a variety of vehicles and it is my favorite.I just got an 02 Focus ZTS that is a close second.This is a low mileage previously granny driven all around nice car.There in lies the problem.It is out of warranty and I want as much power as possible and still be manageable for my pregnant wife.I am sure you all know more than me about them than I do but here is the run down.It is a 2.0 16v DOHC Ztech 5 speed.The only thing I have done is removed the stock air box and put on a Kenne Bell cone air filter.(hand me down from the Neon).What else can I do.I looked at the exhaust and there is alot of restriction there but I dont wanna take out too much cause my wife hates the suond of a copletely open exhaust.Ok now you have a novel to read any help would be really appreciated.
__________________
If it aint broke fix it till it is.
|
|
#2
|
||||
|
||||
|
Re: Need more go go
N/A or boost... what's your budget and how far are you willing to go?
__________________
-Josh- 96' Integra GSR / ITR cams/valvetrain. Skunk2 IM, Greddy evo2, AEM CAI, RMF Header, Megan testpipe, Hasport mounts, Eibach coilovers, Beaks tie bar, Megan H brace, Rota Attacks, F/R strut bar, Kirk 6 point cage, Bride Cugas, Takata 4 Point, ITR Steering wheel 98' SVT Contour, 3L Port-Matched swap with SVT cams/full bolt ons; 224fwhp. 01' Chevy Blazer, DD. |
|
#3
|
|||
|
|||
|
Re: Need more go go
N/A and a tight budget.My wife is pregnant after all.If I go putting a 3000 buck turbo she'll probably go into early labor.
__________________
If it aint broke fix it till it is.
|
|
#4
|
||||
|
||||
|
Re: Need more go go
chip, intake, nice exhaust with a resonator and a silencer (quiet).. i wouldnt go for a header as that will make it louder.. you could do cam gears, UDP.. ported TB. that will give it more go.. if you want more just get a set of nice cams.
__________________
-Josh- 96' Integra GSR / ITR cams/valvetrain. Skunk2 IM, Greddy evo2, AEM CAI, RMF Header, Megan testpipe, Hasport mounts, Eibach coilovers, Beaks tie bar, Megan H brace, Rota Attacks, F/R strut bar, Kirk 6 point cage, Bride Cugas, Takata 4 Point, ITR Steering wheel 98' SVT Contour, 3L Port-Matched swap with SVT cams/full bolt ons; 224fwhp. 01' Chevy Blazer, DD. |
|
#5
|
|||
|
|||
|
Re: Need more go go
If your budget will allow I would also throw in a larger throttle body, like a Mac or Focus Sport 65 mm. Lets it breathe a little better and if you decide to go forced induction, it's one less thing to buy later. <www.batinc.net> was selling JR superchargers recently for $2k if you want some instant pick'em up. For a quiet hi-performance exhaust look here for info <http://www.focaljet.com/shootout_0.html>But I concur with sk8ter, intake and exhaust are the biggest bang for the buck. BTW sk8ter, it wasn't until another post I realized that your Mustang was a model. Nice job, and dopey me for not looking at the background.
|
|
#6
|
||||
|
||||
|
Re: Need more go go
lol
__________________
-Josh- 96' Integra GSR / ITR cams/valvetrain. Skunk2 IM, Greddy evo2, AEM CAI, RMF Header, Megan testpipe, Hasport mounts, Eibach coilovers, Beaks tie bar, Megan H brace, Rota Attacks, F/R strut bar, Kirk 6 point cage, Bride Cugas, Takata 4 Point, ITR Steering wheel 98' SVT Contour, 3L Port-Matched swap with SVT cams/full bolt ons; 224fwhp. 01' Chevy Blazer, DD. |
|
#7
|
||||
|
||||
|
Re: Need more go go
as i am looking at getting a little more punch from the 03 focus that i'm going to buy (just gotta find one lol) a websitethat i found that has helped allot is www.focussport.com, they have everything from superchargers to Cosworth na pakages to cams chips exhaust intake valvetrain etc etc and for te parts they also have dyno charts so you know what power you will be making well you can estimate as all cars respond differently) but i've found it a big help, and good luck (I'd go for a cam the one on focussport gained 17 hp)
__________________
What Is With The Hatred Between Imports and Domestics? In The End, We All Love Cars. |
|
#8
|
||||
|
||||
|
Re: Need more go go
Focussport is a great site, with a great reputation, and all around great parts and service...if you can afford it, get it.
__________________
-Chuck |
|
#9
|
|||
|
|||
|
Re: Need more go go
Damn you guys rock now I have enough websites to shop till after my kid is born.I think I am going to go as far as possible with a NA enging before I go to forced induction.Next question is What about shaving the cyl head to change the compression after I get a little done to the engine?I dont know maybe I'm getting ahead of myself.Thanks guys
__________________
If it aint broke fix it till it is.
|
|
#10
|
|||
|
|||
|
Re: Need more go go
If you're seriously thinking F-I in the later term then don't shave the head. The Zetec already is running at 10:1 and pushing that higher means running premium gas automatically. I don't think the performance gain is worth the cost either when you could put the cash toward something like the exhaust system where you'll see much bigger benefits. Another site you might like to try is www.myzx3.com. Great advice and links.
|
|
#11
|
||||
|
||||
|
Re: Need more go go
another go fast for cheap mod is nitrous..
zetec's respond well to nitrous. 65 shot should be good for atleast mid 14's
__________________
-Josh- 96' Integra GSR / ITR cams/valvetrain. Skunk2 IM, Greddy evo2, AEM CAI, RMF Header, Megan testpipe, Hasport mounts, Eibach coilovers, Beaks tie bar, Megan H brace, Rota Attacks, F/R strut bar, Kirk 6 point cage, Bride Cugas, Takata 4 Point, ITR Steering wheel 98' SVT Contour, 3L Port-Matched swap with SVT cams/full bolt ons; 224fwhp. 01' Chevy Blazer, DD. |
|
#12
|
||||
|
||||
|
Re: Need more go go
http://www.focussport.com/cosworth-manifold.htm this is where you want to go assuming you have the cash to do so, 3 stages the first is a 27 hp boost, second puts you to 200 and third (to be released soon) is 230 and this way, you get Cosworth parts, Cosworth, being one of the best aftermarket companies in the world, so practicly gaurenteed relioability, but good luck dude, and have fun!
__________________
What Is With The Hatred Between Imports and Domestics? In The End, We All Love Cars. |
|
#13
|
|||
|
|||
|
Re: Need more go go
NICE.Like I said you guys really rock but looking at all theese turbos is driving me nuts I want one so bad.I just have to keep it calm fo now for the wife.She likes to get away from the mom mobile(05 Taurus ses) and get in a 5 speed and turn a few heads in a manual.Of course she hates the neon its too rough she says.Oh well less moles on my baby.Thanks again fellas
__________________
If it aint broke fix it till it is.
|
|
#14
|
|||
|
|||
|
Re: Need more go go
head from JohnP, nice cams, gears, udp, intake, plug wires(smooth the dile), shorty header, 2.25in cat back (not as loud as 2.5 but no real difference in performance unless you plan to constantly rev 6500-8000rpm)
__________________
FORMERLY: zx2srdotnet(1,380 posts) 2001 Esxort ZX2 - Traded 2000 Escort ZX2 S/R - Sold 2003 Mustang Mach1 - Totaled 2014 Altima 2.5 S - Purchasing Soon |
|
#15
|
||||
|
||||
|
Re: Need more go go
not that you should take a Zetec past about 7300 without modding it allot more signifcantly, so it can handle the exra revs
__________________
What Is With The Hatred Between Imports and Domestics? In The End, We All Love Cars. |
|
![]() |
POST REPLY TO THIS THREAD |
![]() |
|
|