|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| Let's get Technical! Discussion for hardcore in-depth motor heads! |
 |
 Show Printable Version | 
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
11-04-2005, 01:01 PM
|
|||
|
|||
Can i run a pr4 ecu on a b16a motor swap for now?
ok i own a 89 si hatch an puttin a b16a swap in was wondering if i can just run it off a pr4 for now since i don't have a pr3 or pwo ?
|
|
#2
11-04-2005, 03:12 PM
|
|||
|
|||
|
Re: Can i run a pr4 ecu on a b16a motor swap for now?
as long as you have a obd0 pr4 then yes you can run it no problems
|
|
#3
11-04-2005, 03:14 PM
|
||||
|
||||
|
Whiskey Tango Foxtrot
__________________
RTC Great Lakes NATTC Pensacola CVN-68 U.S.S. Nimitz San Diego 93 Del Sol D16Z6 Greddy 4-2-1 Greddy Evo2, AEM cold air MSD Ignition wires 15' GSR rims http://www.myspace.com/ghostryders Last edited by Airdale Mech.950; 11-06-2005 at 11:21 AM.
|
|
#5
11-04-2005, 05:15 PM
|
|||
|
|||
|
Re: Can i run a pr4 ecu on a b16a motor swap for now?
Quote:
|
|
#6
11-04-2005, 05:49 PM
|
|||
|
|||
|
Re: Can i run a pr4 ecu on a b16a motor swap for now?
Quote:
 , you can, but there are much cheaper routes to go.you can use the pr4, but, you will be missing your vtec fuel maps. can be used temporarily, but, stay out of vtec. many ls swappers are looking for your pr4. why dont you just sell it and get a PR3 or PWO?
__________________
99 [email protected] psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me.
|
|
#7
11-05-2005, 12:49 PM
|
|||
|
|||
|
Re: Can i run a pr4 ecu on a b16a motor swap for now?
well im thinkin about doin that or im just thinkin about goin obd1 u know the jumper harness so i don't know im just hoping this swap is just a plug an play thing u know no custum harness shyt
|
|
#8
11-05-2005, 03:26 PM
|
|||
|
|||
|
Re: Can i run a pr4 ecu on a b16a motor swap for now?
if your going obd1, then you need a obd1 or obd2 distributor, 4 wire o2 sensor, obd0-obd1 jumper harness, and a obd1 ecu.
|
|
#9
11-08-2005, 02:42 AM
|
||||
|
||||
|
go obd1,
__________________
Location: Logan Utah Black 1990 CRX Si FI d16a6 R.I.P 1995 DC Integra LS jdmb18b w/ ys1 trans SOLD 1990 EF civic Si sohc ninja project Traded 1992 EG vx hatch sohc turbo/gsr swapped SOLD 1992 DA9 obd1 love, non-vtec love project
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
