|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| Off-Topic Talk about anything other than cars. |
 |
 Show Printable Version | 
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
08-30-2005, 04:22 PM
|
|||
|
|||
|
looking for scantool, stalling problem..
car: eclipse 95 gs(non-turbo)
OBD 1 with obd 2 plug style... i'm looking for a scantool so that i can monitor my car while i'm driving, i wanted one that i can hookup to a laptop, but i can't find one that supports my car... so if u know a good scantool that will work on my car, let me know. thanks... trying to solve my stalling problem, no check engine light comes on, nothing in computer memory when scanned later, so i wanted to try catching it with a scanner while i'm driving.. is the cheap scantools at kragen and autozone good for what i want to do?? replaced ign.coil pack, ign.wires, sparkplugs, and crankshaft sensor... it still stalls.... i might replace VSS to see if that fixes the problem...if u think u know whats wrong, let me know...thanks... Last edited by azn_mien; 08-30-2005 at 06:31 PM. 
|
|
#2
08-31-2005, 07:06 AM
|
||||
|
||||
|
Re: looking for scantool, stalling problem..
Your car is OBD-II not OBD-I.
Check out www.pocketlogger.com Most of the scan tools at AutoZone/Advanced are just for retreiving CEL's. If you do find one that will show you all of the OBD-II parameters, you probably won't be able to save a log. I would recommend a pocketlogger. You can pick up a palm on ebay for about $15. Enjoy!
__________________
 1997 Spyder GS-T 5-Speed EVO III 16g, DSMLink, Walboro 190 lph Fuel Pump, FIC 650cc injectors, CoolingMist 150psi Methanol Injection, Greddy EVO 2 Cat Back, 2.5" Extreme DP, 2.5" Extreme Hi-Flow Cat, Injen intake, HyperDrive C1 Street Disk & PP, HyperDrive Lightweight Flywheel, 1g BOV, RRE UICP, Home Depot MBC, AEM UEGO WBO2, Brembo Slotted rotors, Akebono Ceramic Pads
|
|
#4
09-21-2005, 03:48 PM
|
|||
|
|||
|
Re: looking for scantool, stalling problem..
just want to let ya know, or anyone that has a 1995 car, that has OBD 2 plug style, even if it says OBD 1 certifed under the hood, OBD 2 scanners still work on it... cause i just got Proscan obd 2, hooked it up to my car and laptop, and it works...
|
|
#5
09-21-2005, 08:57 PM
|
||||
|
||||
|
Re: looking for scantool, stalling problem..
It's OBD1 compliant because OBD2 wasn't required until 96. It is still OBD2 which complies with OBD1 standards.
__________________
I'm>everything
|
|
#6
09-21-2005, 09:14 PM
|
|||
|
|||
|
Re: looking for scantool, stalling problem..
if there is no cel a scan tool wont do you any good. def get a logger.
|
|
#7
09-21-2005, 09:15 PM
|
|||
|
|||
|
Re: looking for scantool, stalling problem..
check fuel filter(s)
|
|
#8
09-21-2005, 11:51 PM
|
|||
|
|||
|
Re: looking for scantool, stalling problem..
yea, proscan odb 2 is a logger(using laptop), http://www.myscantool.com but i'm not sure how to figure out which part of the car is faulty that cause my stalling...
so far replaced Fuel filter, spark plugs, ign.wires, ign.coils, crankshaft sensor and oil filter.... i wanted to replace Vehicle speed sensor, but i can't find it on my tranny... http://www.angelfire.com/hero/azn_mien/car.html drawing from alldata and picture of my tranny showing its not where it suppose to be, dunno where it is... right now i'm just playing the obd 2 software and trying to understand it...
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
