skyline gtr/gtst parts

[MR2GTR33]

one set of gtr 32 turbos just rebuild 1000kms ago standard. $1200pair

one gtr33 highflow with steelwheels just been rebuild 2000kms $820

one standard 33gtst turbo $570

one t3/t4 garret in good condition needs wastegate $900

turbonetics wastegate (racegate) 42mm in good condition $650

wiesco forged pistons for toyota 3sgte 40thow over only done 1000kms still perfect $600

intercooler core 600x300x75 bar&plate garret core brand new $650

gtr33 seats in good condition $1390 the pair

gtr33 crank in perfect condition $380

gtr33 original manifolds and dumps and waterlines and hoses $offers?

gtr33 or 33gtst RSRcat-back exhaust sysytem 3/5' polished stanless as new.$750ono

gtr33 pair of air flow meters $700

gtst33 airflow meter $190

gtr32 or gtst32 original carmats full set front & back $100

[MR2GTR33]

greddy gauges oil-temp electronic white face complete withh everything to install as new $400

autometer oil-pressure gauge pro comp liqurd-filled black face with cup holder $90

itsmefashions@hotmail.com

can supply photos on some parts

[Spec2 Girl]

I don's suppose you have a rear strut bar for an R33 GTR???

[MR2GTR33]

i can get a hold of one if your intrested? i also have some ajustble front caster rods for gtst33 asking$390

[Spec2 Girl]

Originally posted by MR2GTR33
i can get a hold of one if your intrested?

Yes, I may be interested depending on price. If you send me a PM if you find one and what cost you’re looking at, we can go from there. Thanks

[Mick]

Do u still have the exhaust ?

Is it made for a gtr or gtst ?
bec they are slightly different.
Where about are you ?

Also do u have a front and rear strut brace for a gtst ?

[MR2GTR33]

the exhaust bolt straigt onto the gtst and for the gtr you have to run a spacer flange plate inbetween in two flanges at the rear muffler and fits perfect. i have tryed it on my gtr and my gtst.

[MR2GTR33]

here is a pic of the exhaust. it looks like this but its not this one, mine is in better condition.

[CA31_JR]

Have you still got the intercooler or can get your hands on one. I'm after a standard Skyline GTR intercooler at a good price

[MR2GTR33]

the apexi one has been sold but i can get a core for a gtr

[CA31_JR]

basically what I was looking for was just a standard factory GTR intercooler. I'm going to fit it to my RB20DET powered Cefiro. I only need the intercooler as I will get someone to fabricate the piping for me.

By core I assume that comes with the inlet and outlet pipes and mounting points?

Ta.

[MR2GTR33]

its just a core and its brand new, bar and plate 3' thick

here is a pic of my car with the same intercooler but mine is 3/5' thick and it made 40hp @ the wheels more on the same boost than the standard gtr intercooler. i dont have brakets or end tanks but you can get your fabracator to make them and it will still cost cheaper than a gtr intercooler.

[CA31_JR]

what price is on the core?
And how much would the end tanks and brackets cost to fabricate roughly?
I can get a complete secondhand GTR intercooler for $950 which seems to be the best price I've seen so far....

Any recommendations on fabricators in Sydney area?

[MR2GTR33]

roughtly 150-200 for the end tanks and brackets and $650 for the core and it would be a much thicker than the gtr core and would flow much better.

[CA31_JR]

Thanks for the info!!