My dyno graph (for those of you who wanted to see it)

[JustinP10]

Here it is. The blue line is what i put down back in December. that is with Intake, header, and advanced timing (about 17 i thought). The red line is my new dyno, done on 4/22/01. That added pullies, flywheel, clutch (if that counts), and a few more degrees of timing advance since my last pull. What do you think? Any comments, suggestions???

[JustinP10]

dumb computer, doesn't like me. let me try this again.

[GTO-TT/Chev57]

That's good hp, looks like you had a engine miss in the first run with all those spikes in it. Shouldn't have them in it that close together.

[b-b00gie]

Nice improvement on the HP and torque, and less spiking now too. Keep it going!!

[JustinP10]

Originally posted by GTO-TT/Chev57
That's good hp, looks like you had a engine miss in the first run with all those spikes in it. Shouldn't have them in it that close together.

Yeah, It didn't feel like i was missing or down on power when i first dynoed my car (I had only had this G20 for about 6 weeks at the time), but i noticed the jagged line, so i did a tune-up (cap, rotor, and plugs) and it did seem to get back a couple hp too.

[02G20T]

I live in Chandler, drag that thing out this way so I can check it out.

[JustinP10]

Originally posted by 02G20T
I live in Chandler, drag that thing out this way so I can check it out.

Really? Cool, there is another list member in Chandler too, Kyle. He's on this forum now too. Do you know about the Az list? Here's the link if not.

AZ List

[SkylinesKillAll]

so you got 1.1hp from the stock 140 and 1.4 ft lbs of torque from the stock 132 after all that modification? doesnt seem like its worth it to me.

[JustinP10]

Originally posted by SkylinesKillAll
so you got 1.1hp from the stock 140 and 1.4 ft lbs of torque from the stock 132 after all that modification? doesnt seem like its worth it to me.

No, those numbers are at the wheel horsepower and torque, rather than flywheel power. Wheel horsepower is about 15% less ( i think it varies a lot depending on your setup too, wheels, alignment, etc...). So i'm about 160-165hp and 150-155ft.lbs to the flywheel. I'm up about 20-25hp and 18-23ft.lbs of torque from stock These are all guesstimations of course.

[G-Forces]

Hehe, Justin is right. I dyno'd my car stock to get a baseline last year. 124whp and 118tq. Then I dyno'd again with Intake, exhaust and pullies. 135whp and 124tq. So if you think about 124/140 that's about a 13% drivetrain loss then at 135whp I should be seeing around ~153hp at the flywheel. Not to shabby for my limited mods.

Now that I got S3 cams in and the HS header going in this weekend I can't wait to see what I get when I dyno again this summer.

[Nismoboy1]

Originally posted by SkylinesKillAll
so you got 1.1hp from the stock 140 and 1.4 ft lbs of torque from the stock 132 after all that modification? doesnt seem like its worth it to me.

actually he's pulling very good numbers, good job...consider that dyno runs are measured at the wheels not the crank, those numbers your talking about, the 140hp/132lb is just the hp at the crank. If you wanna talk about crank hp, he's probably pulling somewhere's around 160-165hp and about 150lbs of torque. Keep it up Justin...your up there with some of these guys in here...

www.se-r.net/car_info/dyno/index.html
www.se-r.net/car_info/dyno/others.html
www.se-r.net/car_info/dyno/dyno_day_1999.html

[Nismoboy1]

btw with numbers like that, and just a little more tuning, you can easily break into the 14's if not low 15's...SI's beware haha

go here www.clubsi.com/dyno.shtml you'll see what i'm talking about, did you know a stock SI only puts about 98lbs of torque to the wheels haha damn and I thought my old ga16de had crappy torque :finger:

[SkylinesKillAll]

oh yeah stupid me. :buck: i forgot about the driveline loss my bad. goos job justin keep up the good work.

[DVSNCYNIKL]

That is a very impressive chart. With little mods, you've got that much change. I need to start getting my stuff done. What mods do you have left to install if you don't mind me asking?

[Dprotech]

alright ...way too much math ....are we racers or Einsteins or both ...

hehe ..Jason ..when are you going to call a meet for us Ontario G Owners ?:frog: