-
Grand Future Air Dried Fresh Beef Dog Food
Air Dried Dog Food | Fresh Beef

Carnivore Diet for Dogs

Go Back   Automotive Forums Car Chat > Honda > Exterior | bodykits | Lighting
Register FAQ Community
Exterior | bodykits | Lighting When your ready to showoff that 'H' ride, here's your forum!
Reply Show Printable Version Show Printable Version | Subscription Subscribe to this Thread
 
Thread Tools
  #1  
Old 06-14-2004, 01:41 PM
civic99babe civic99babe is offline
AF Newbie
 
Join Date: Jun 2004
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Post Moisture in angel eye headlights

My headlights have a ton of moisture in them. The whole light is almost covered up by moisture. I have a 99 Civic-please help!! Any suggestions of what I could do would be very helpful!!
THX!
Reply With Quote
  #2  
Old 06-14-2004, 01:43 PM
emerge's Avatar
emerge emerge is offline
AF Enthusiast
 
Join Date: Dec 2001
Posts: 924
Thanks: 0
Thanked 0 Times in 0 Posts
Send a message via AIM to emerge Send a message via Yahoo to emerge
Re: Moisture in angel eye headlights

You should've searched. There's several threads about this topic on this board. Anyways, since your a newb I'll offer you two solutions:

1. Take the light out, and angle it so that the water can drip out (I used the hole for the turn signal bulb). Place it in the sun or somewhere hot so that the water will condense.

2. Drill a hole in the bottom of the housing so that the water has a place to escape.
__________________
Stephen Gladney
Original PH Member


EJ8 Civic | AIM: nxzo | www.rtek.org
Reply With Quote
  #3  
Old 06-14-2004, 03:57 PM
96Civic_Coupe 96Civic_Coupe is offline
Banned
 
Join Date: May 2004
Posts: 114
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Moisture in angel eye headlights

or, put your oem headlights back on
Reply With Quote
  #4  
Old 06-14-2004, 08:51 PM
Ricochet's Avatar
Ricochet Ricochet is offline
Banned
 
Join Date: Jun 2003
Posts: 5,591
Thanks: 0
Thanked 1 Time in 1 Post
Re: Moisture in angel eye headlights

I've found they don't get as bad if you leave the rubber caps off the rear.. they'll build up a bit in the inner corner but go away soon after, especially if left in the sunlight.
Reply With Quote
  #5  
Old 06-15-2004, 12:54 AM
integrasedan integrasedan is offline
AF Enthusiast
 
Join Date: Nov 2003
Posts: 463
Thanks: 0
Thanked 0 Times in 0 Posts
check to see if you have any cracks where water can get in like when you wash the car.

i would use silicone sealant around the edges where the headlight is sealed just in case the old seals are leaking.
Reply With Quote
  #6  
Old 06-15-2004, 07:51 PM
eckoman_pdx's Avatar
eckoman_pdx eckoman_pdx is offline
Honda God
 
Join Date: May 2003
Posts: 3,780
Thanks: 0
Thanked 7 Times in 6 Posts
Send a message via AIM to eckoman_pdx Send a message via Yahoo to eckoman_pdx
Okay now, drilling holes in your headlights isn't the smartest idea. This hole drilling idea is getting out of hand. You don't need a place for the water to drain buy "drilling holes," you need to seal them better, after all they are leaking and fogging because they arn't sealed properly. The seals they came with are leaking. They are cheaply made, and have cheap seals. Try taking the rubber caps off like Ricochet said, or park it in a garge or take the headlights off and let them sit overnight inside...let them basicially dry out.

Now, get soem silicion sealent, and run a bead all the way around the headlight seems. You basically need to reseal it, since the seal it has leaks. Water it getting in there because these aftermarket companies do a piss poor jpb of sealing the lights. Re-sealing them properly with slicion should keep the water from getting in by prodiving a seal...which is the reason OEM lights don't leak usually, they are properly sealed.
Reply With Quote
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums Car Chat > Honda > Exterior | bodykits | Lighting


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 12:01 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts