-
Grand Future Air Dried Fresh Beef Dog Food
Air Dried Dog Food | Fresh Beef

Carnivore Diet for Dogs

Go Back   Automotive Forums Car Chat > Oldsmobile > Aurora
Register FAQ Community
Reply Show Printable Version Show Printable Version | Subscription Subscribe to this Thread
 
Thread Tools
  #1  
Old 05-04-2004, 11:01 PM
oldaurora oldaurora is offline
AF Newbie
 
Join Date: May 2004
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
keyless remote

I have a 98 aurora,one of my keyless entry units stopped working after a battery replacement.Can anyone tell me how to reprogram it. thanks. ps.is there a primary and secondary receiver,and how can i tell the difference if there is?
Reply With Quote
  #2  
Old 05-05-2004, 11:25 AM
RoraStar96's Avatar
RoraStar96 RoraStar96 is offline
AF Enthusiast
 
Join Date: Mar 2004
Posts: 435
Thanks: 0
Thanked 0 Times in 0 Posts
Send a message via AIM to RoraStar96 Send a message via MSN to RoraStar96 Send a message via Yahoo to RoraStar96
Re: keyless remote

This was posted by MoshimoGTP in another thread...

Quote:
----PROGRAMMING----

Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation
__________________
1997 Aurora

"Aurora Snow"
250++HP 4.0L Modified Aurora V8 w/Autobahn Performance
On Deck: RSM intake, RSM 80mm TB

Administrator, www.oldsmobileforums.com
Administrator,Aurora Club of North America
Administrator, www.bonnevilleclub.com
Adminstrator, www.ontariobonnevilleclub.com Coming Soon
Reply With Quote
  #3  
Old 05-05-2004, 04:45 PM
oldaurora oldaurora is offline
AF Newbie
Thread starter
 
Join Date: May 2004
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
rorastar96,thanks for the input.i checked owners manual and my fuse block doesnt show a mall pgm fuse,there is a pcm fuse in slot number 10 that controls powertrain control module,vats pass-key II. Could this be it? thanks
Reply With Quote
  #4  
Old 05-05-2004, 06:05 PM
RoraStar96's Avatar
RoraStar96 RoraStar96 is offline
AF Enthusiast
 
Join Date: Mar 2004
Posts: 435
Thanks: 0
Thanked 0 Times in 0 Posts
Send a message via AIM to RoraStar96 Send a message via MSN to RoraStar96 Send a message via Yahoo to RoraStar96
Re: keyless remote

That write up that I posted came from a GP GTP owner, so it may not be exactly the same, I just fired that off from memory.

VATS Pass key definitely is involved with your remote so its a good chance it may be it
Reply With Quote
  #5  
Old 05-10-2004, 01:43 AM
dsatt12 dsatt12 is offline
AF Enthusiast
 
Join Date: Oct 2003
Posts: 410
Thanks: 0
Thanked 0 Times in 0 Posts
Re: keyless remote

Look here. It was pretty well covered.

http://www.automotiveforums.com/vbul...rogram+keyless
Reply With Quote
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums Car Chat > Oldsmobile > Aurora


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:34 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts