Honda NSR500 (1984)

[imster]

Originally Posted by Veyron

Fantastic build!

Where can I find Marco's building jig?

Thanks Veyron!

I will PM you the details mate

[John18d]

Originally Posted by imster

Thanks Veyron!

I will PM you the details mate

Imster - I already Pm'd Veyron Mark Stearney's email address regarding the bike jig.

Hey Imster - incidentally what section on Mac's website is the Barchetta spiral wrap??

Cheers
John

[imster]

Originally Posted by John18d

Imster - I already Pm'd Veyron Mark Stearney's email address regarding the bike jig.

Hey Imster - incidentally what section on Mac's website is the Barchetta spiral wrap??

Cheers
John

Just click on "Finishing Materials" on the left hand side and then scroll just past halfway on that page and you should see it

[John18d]

Originally Posted by imster

Just click on "Finishing Materials" on the left hand side and then scroll just past halfway on that page and you should see it

Thanks Imster - I found it a few minutes after I posted the question - I'm not sure why Mac didn't have those items in say "MotoGP store" tab under detail parts.

Mac knows there's lots of problems with the old website and I have been to his place in Phoenix to see that he has paid a lot of money for a new website page but the new website has many problems with it too that Mac is trying to fix before he implements it.
He has been very frustrated by the website designer.

Thanks again for the reply Imstr

Cheers
John

[sebasoakley]

Its fantastic clean job, excellent.
Please what do you use to do the ties on the forks protectors?
Thanks very much and congratulations.

[John18d]

Originally Posted by sebasoakley

Its fantastic clean job, excellent.
Please what do you use to do the ties on the forks protectors?
Thanks very much and congratulations.

Sebasoakley - I am not 100% positive on the ties that were used for the 84' Honda NSR500 forks, but I believe they are "tie wraps" from Model Factory Hiro and they come in sets of Black or White.

Imster did one hell of a job on the 84' NSR500 - his best work to date for attention to details and the BEST 84' NSR500 on the forum to date in my opinion.
I can only hope when I am out of the hospital in 3 & 1/2 months time the one I plan to build will come out half as good as the one built by Imster.

I Hope this can help you identify the wraps Sebasoakley.
Cheers
John

[imster]

Originally Posted by John18d

Sebasoakley - I am not 100% positive on the ties that were used for the 84' Honda NSR500 forks, but I believe they are "tie wraps" from Model Factory Hiro and they come in sets of Black or White.

Imster did one hell of a job on the 84' NSR500 - his best work to date for attention to details and the BEST 84' NSR500 on the forum to date in my opinion.
I can only hope when I am out of the hospital in 3 & 1/2 months time the one I plan to build will come out half as good as the one built by Imster.

I Hope this can help you identify the wraps Sebasoakley.
Cheers
John

Apologies for not replying sooner, been very buys with house moves and other stuff!

The tie wraps were made from plasticard because when I built this the MFH tie wraps were not produced yet. I cannot remember the thickness of the plasticard but it was very thin (almost like paper) and clear. so you sand the surface to give it the cloudy colour and then cut into tiny strips then just anchor down with CA glue and the rest is straightforward!

Once again sorry for the delayed reply and thanks heaps John for the nice comments. I hope your recovery goes well

[tytax]

What's happend with photos? It's the best WIP and I'm planning to use it as a reference (

[imster]

Originally Posted by tytax

What's happend with photos? It's the best WIP and I'm planning to use it as a reference (

Hey man, send me a PM and I will give you the info

[imster]

If anyone wants the photos and the full build write up for this please contact me via PM thanks!