|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| '88 - '91 Civic | CRX | Wagon | Shuttlee Partnership with: LadyNRedSi.com |
 |
 Show Printable Version | 
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
10-21-2002, 08:45 PM
|
||||
|
||||
|
MELT DOWN!! Need ZC PARTS
Well this has ben just a GREAT Monday, on the way home from work this evening i hear this noise under the hood and then a screeching sound, well i can pull over i am on a very large 2 lane Damn with no burms (I have to cross a lake to get home) well i am driving along slowed down a bit hoping to make it the other side and just as i was pulling off i heard belt screeching again and then the motor cut off.
I opened the hood and just about cried, i looked down inside to see the timing cover melted down and the belt was off melted threw the cover that is and looked deeper to seel the crankpulley had also came off and broke the alternator belt. I did have parts at home and tools is the car that i could put the belt back on limp it home. A list of what i need from you Guys Or Gals I hope: Upper and lower timing covers DOHC ZC Crank Pully What i can get local: Timming belt Alt Belt Key way to set pulley in place Crank bolt and washer Couple ? Is this an Interferance motor (does the valves hit the pistons when the belt brakes) I did drive the car home but could not tell for sure if it was ok. Will the crank pully off the stock si motor work that is what i used to get home? but is it right for the motor it does look totaly differant. where can i get these parts from if nobody on here has them? is there a beter than stock crank pulley that I can get for this motor. where and how much? Thanks For all the help and info
__________________
MY MONEY PITs!!! 2001 Silverado-----------90 Civic Si 4.8 V8---------------------ZC DOHC Power K&N------------------------Intake 2" in the back-------------3.5 Eibach Rollin on 20's--------------15" AR wheels Pioneer head--------------Panisonic head JL 10w6--------------------Infinity Ref  http://community.webshots.com/album/49425207zKoYto 
|
|
#2
10-21-2002, 08:57 PM
|
||||
|
||||
|
Re: MELT DOWN!! Need ZC PARTS
Quote:
Timing belt you will need is from a 88 prelude. Alternator belt from a 88-91 Si
|
|
#3
10-22-2002, 05:28 AM
|
||||
|
||||
|
Re: Re: MELT DOWN!! Need ZC PARTS
Quote:
Well thats what i was thinking but the pully is heavy campered to the zc pully. will it hurt anything.
__________________
MY MONEY PITs!!! 2001 Silverado-----------90 Civic Si 4.8 V8---------------------ZC DOHC Power K&N------------------------Intake 2" in the back-------------3.5 Eibach Rollin on 20's--------------15" AR wheels Pioneer head--------------Panisonic head JL 10w6--------------------Infinity Ref http://community.webshots.com/album/49425207zKoYto
|
|
#4
10-22-2002, 09:55 AM
|
|||
|
|||
|
MAN that sucks about your car. but the only thing that i have that is ZC is a head complete with cams and all valve train comp. that has been cleaned and crack tested with die, if you want it its 4 sale. i need to get rid of it.
__________________
:smoker2:kaytec4door:smoker2: mods done: AEM cold air intake, ractive racing cat, ractive axel back exhaust, NGK plugs, nuespeed cross-drilled rotors, EBC the green stuff pads, projecter headlights, clear corners, carbon fiber tails, Z3 fenders, adjustable coilovers, Konig flatline rims with dunlop fm901 (17*7), full complete sound system with two 10'' subs, kenwood 600w amp, punch cap, pionner speakers all the way around, full custom interior paint job, reverse indiglo guages, aluminum gauge bezel, d16a6 head swap polished, 4-2-1 ceramic coated header, :finger4: proud member of team kay tec:finger4:
|
|
#5
10-22-2002, 05:31 PM
|
||||
|
||||
|
Quote:
__________________
MY MONEY PITs!!! 2001 Silverado-----------90 Civic Si 4.8 V8---------------------ZC DOHC Power K&N------------------------Intake 2" in the back-------------3.5 Eibach Rollin on 20's--------------15" AR wheels Pioneer head--------------Panisonic head JL 10w6--------------------Infinity Ref http://community.webshots.com/album/49425207zKoYto
|
|
#6
10-23-2002, 05:52 PM
|
||||
|
||||
|
Nobody has any parts for the zc, how about what might interchange with the ZC come on people i have faith in you help me find some covers so i can get back on the road again.
Also does anybody no what valve cover gasket i need to get for the ZC
__________________
MY MONEY PITs!!! 2001 Silverado-----------90 Civic Si 4.8 V8---------------------ZC DOHC Power K&N------------------------Intake 2" in the back-------------3.5 Eibach Rollin on 20's--------------15" AR wheels Pioneer head--------------Panisonic head JL 10w6--------------------Infinity Ref http://community.webshots.com/album/49425207zKoYto
|
|
#7
10-31-2002, 11:27 AM
|
|||
|
|||
|
yea the head is stock but it has about 115k miles on it. im asking around 80$
__________________
:smoker2:kaytec4door:smoker2: mods done: AEM cold air intake, ractive racing cat, ractive axel back exhaust, NGK plugs, nuespeed cross-drilled rotors, EBC the green stuff pads, projecter headlights, clear corners, carbon fiber tails, Z3 fenders, adjustable coilovers, Konig flatline rims with dunlop fm901 (17*7), full complete sound system with two 10'' subs, kenwood 600w amp, punch cap, pionner speakers all the way around, full custom interior paint job, reverse indiglo guages, aluminum gauge bezel, d16a6 head swap polished, 4-2-1 ceramic coated header, :finger4: proud member of team kay tec:finger4:
|
|
#8
10-31-2002, 11:45 AM
|
||||
|
||||
|
Quote:
www.acuraautomotiveparts.net
__________________
-Shawn '91 Civic DX sedan DOHC ZC, I,H,E, urethane bushings and mount inserts, rock chipped hood, some rust, stock steelies, nice comfy Integra seats, and the A/C works! What else could you want from an 18 year old car with 241,000 miles? Working on getting the Si tranny in now 
|
| ||||||||||||||||||||||||||||||||||||||
|
POST REPLY TO THIS THREAD |
 |
|
|
