|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
#1
10-05-2006, 01:31 AM
|
||||
|
||||
1988 Cherokee Pioneer Project
Hello all,
Thanks for any help you have given so far, and the future help I hope to get. I have been on here a couple of times, and posted a few. Here is my website link with my 1988 Jeep Cherokee pics from after I installed the Pro Comp 3" Suspension lift. I am about to do more, and will pst new pics as soon as I can. http://raceghost.myftp.org/gallery/Jeep.html
__________________
Raceghost Rocket powered now... 88 Jeep Cherokee Pioneer (Rebuilt). 00 Honda RC51 (...whispers of super bad!) 04 Mitsubishi Evolution VIII (Finally!)  Lead, Follow, or get the f... out the way
|
|
#2
10-05-2006, 02:03 AM
|
||||
|
||||
|
Good Parts site by the way
Here is a cool site you may or may not have heard of, but they have a lot of Jeep parts....
http://www.thepartsbin.com/ Just ordered all these parts from "The Parts Bin"...Keep you posted on how shipping goes and quality when they get here. Power Stop Cross Drilled Brake Rotors http://performance.thepartsbin.com/b...8&brandid=2234 Power Stop Brake Pads http://performance.thepartsbin.com/b...2&brandid=2234 Jacobs Distributer Cap and Rotor http://performance.thepartsbin.com/b...3&brandid=1982 Nology Profire Ignition Coil http://performance.thepartsbin.com/b...0&brandid=2210 JACOBS-SPARK PLUG WIRE SET - Pro Fit Silicone http://performance.thepartsbin.com/b...4&brandid=1982
__________________
Raceghost Rocket powered now... 88 Jeep Cherokee Pioneer (Rebuilt). 00 Honda RC51 (...whispers of super bad!) 04 Mitsubishi Evolution VIII (Finally!) Lead, Follow, or get the f... out the way
|
|
#3
10-05-2006, 07:01 AM
|
||||
|
||||
|
Re: 1988 Cherokee Pioneer Project
Looks like it's shaping up well! Thanks for the parts site address....
__________________
Ours: 2020 Jeep Wrangler 2.0, 53k 2013 Toyota FJ Cruiser, 84k Kids: 2005 Honda CRV, 228k
|
|
#4
10-22-2006, 10:45 PM
|
||||
|
||||
|
Re: 1988 Cherokee Pioneer Project
All the goodies I ordered....
Jacobs stopped producing the wires and the cap and rotor assembly. Parts bin only had the accel stuff. I think I might go with some MSD wires, or if any one has a better suggestion...? Plus, the 80/140 amp high output alternator, the birth certificated showed the tested amperage to be 88 amps at 1500 RPMS idle, and 160 at 6000 rpms. I know my jeep revs a little slower on the idle, and I think they top out near the range, so hopefully I made a good choice on that. http://raceghost.myftp.org/My%20pict...p/IMG_1905.JPG http://raceghost.myftp.org/gallery/Jeep.html
__________________
Raceghost Rocket powered now... 88 Jeep Cherokee Pioneer (Rebuilt). 00 Honda RC51 (...whispers of super bad!) 04 Mitsubishi Evolution VIII (Finally!) Lead, Follow, or get the f... out the way
|
|
#5
11-08-2006, 04:01 PM
|
||||
|
||||
|
Re: 1988 Cherokee Pioneer Project
Well, I got all the parts installed!!!
 80/140 amp high output alternator Accel Distributer Cap Accel Distributer Rotor Accel Spark Plug Wires Bosch Platinum Spark Plugs Power Stop Cross Drilled Rotors and Pads New Water Pump I have the Nology High Output Coil, but need a wiring diagram to get installed, do to the integrated 3 conductor plugs on the stock coil...  ...Anyone....Anyone...I still need to by the Yellow Top battery. I am looking into Rhino Coating the Outside, or Linex-ing the outside. Then I will tint the windows. Then, next year I will start on the interior. I have plans for a full internal Roll Cage, with 4 Bucket Seats, with 5 point harnesses. Rock on fellas, L8's, Raceghost
__________________
Raceghost Rocket powered now... 88 Jeep Cherokee Pioneer (Rebuilt). 00 Honda RC51 (...whispers of super bad!) 04 Mitsubishi Evolution VIII (Finally!) Lead, Follow, or get the f... out the way
|
|
 |
POST REPLY TO THIS THREAD |
 |
|
|
