|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
#1
01-22-2006, 02:25 PM
|
||||
|
||||
|
Dyno
hey, i am in the St.Louis area and i am wanting to know where a local dyno is? where and how can i find them. I want to get my car tested to see the numbers.
__________________
95 Z71 Silverado 4x4 ext. cab Mods- Flowmaster Exhaust,Intake 
|
|
#2
01-22-2006, 02:58 PM
|
||||
|
||||
|
Re: Dyno
i wouldnt....its depressing....
__________________
92 z28 camaro 5.7 TPI current - slp intake runners and base-BBK 52mm throttle body-MSD 8.5mm wires, blaster coil, and 6AL Box-edelbrock headers-160 degree stat.-hotchkis strut tower brace waiting in the garage - LQ4, milled heads 317 casting (10.5 to 1), hardened pushrods, ported LS6 oil pump, manley dual spings with titanium retainers, MTI X1 cam, hawks longtube headers 
|
|
#3
01-22-2006, 02:58 PM
|
||||
|
||||
|
Re: Dyno
id rather be ignorant until some good power mods are done...
__________________
92 z28 camaro 5.7 TPI current - slp intake runners and base-BBK 52mm throttle body-MSD 8.5mm wires, blaster coil, and 6AL Box-edelbrock headers-160 degree stat.-hotchkis strut tower brace waiting in the garage - LQ4, milled heads 317 casting (10.5 to 1), hardened pushrods, ported LS6 oil pump, manley dual spings with titanium retainers, MTI X1 cam, hawks longtube headers
|
|
#4
01-22-2006, 02:59 PM
|
||||
|
||||
|
Re: Dyno
ya i know, i was going to do a befor and after, so i wanted proof about the hp now and when i am done.
__________________
95 Z71 Silverado 4x4 ext. cab Mods- Flowmaster Exhaust,Intake
|
|
#5
01-22-2006, 03:11 PM
|
||||
|
||||
|
Re: Dyno
most places around here want 80-100 dollars for 3 pulls. Put that money into some good plugs wires and a high output coil. It will be much more satisfying
__________________
92 z28 camaro 5.7 TPI current - slp intake runners and base-BBK 52mm throttle body-MSD 8.5mm wires, blaster coil, and 6AL Box-edelbrock headers-160 degree stat.-hotchkis strut tower brace waiting in the garage - LQ4, milled heads 317 casting (10.5 to 1), hardened pushrods, ported LS6 oil pump, manley dual spings with titanium retainers, MTI X1 cam, hawks longtube headers
|
|
#6
01-22-2006, 03:29 PM
|
||||
|
||||
|
Re: Dyno
good point, and that was another queston, what is a good distributer to get? msd? i was looking in to that and a msd 6a box.
__________________
95 Z71 Silverado 4x4 ext. cab Mods- Flowmaster Exhaust,Intake
|
|
#7
01-22-2006, 09:56 PM
|
||||
|
||||
|
Re: Dyno
i would stay basic for now. Get some mallory or msd 8.5's or bigger wires, jacobs c-4 coil, and some ngk plugs. Id do one project at a time though. Work on your intake and exhaust then move on from there.
__________________
92 z28 camaro 5.7 TPI current - slp intake runners and base-BBK 52mm throttle body-MSD 8.5mm wires, blaster coil, and 6AL Box-edelbrock headers-160 degree stat.-hotchkis strut tower brace waiting in the garage - LQ4, milled heads 317 casting (10.5 to 1), hardened pushrods, ported LS6 oil pump, manley dual spings with titanium retainers, MTI X1 cam, hawks longtube headers
|
|
 |
POST REPLY TO THIS THREAD |
 |
|
|
