|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| '88 - '91 Civic | CRX | Wagon | Shuttlee Partnership with: LadyNRedSi.com |
 |
 Show Printable Version | 
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
12-09-2005, 09:15 PM
|
||||
|
||||
Crank pulley remover tool!!!!!!
hey was wondering anybody knows where I can pick up a Crank pulley remover tool...I know they make them so its so much easier taking off the main pulley bolt...but I cant find a place to buy it anybody know???
__________________
90 Honda CRX Si -Red/Black -B20B/b16 -AEM CAI -/\- Apexi GT Header/2¼" Custom Dynomax Exhaust -Tein SS CoilOvers with pillow ball monuts -/\- ST Swaybars/Energy Suspension Bushings -16x7 Lightweight Rotas -/\- Pro Stop Rotors -/\- Goodridge S.S. Brake Lines -Skunk2 Shifter -/\- MoMo Steering Wheel 
|
|
#2
12-09-2005, 09:38 PM
|
||||
|
||||
|
Re: Crank pulley remover tool!!!!!!
Most larger auto parts stores rent such items if you don't want to own it. But I'd assume Sears or Snap-on, etc would carry a puller like you described. GL
|
|
#3
12-10-2005, 04:55 AM
|
||||
|
||||
|
Re: Crank pulley remover tool!!!!!!
found the kit and here it is for some you never seen it before...
http://cgi.ebay.com/ebaymotors/ws/eB...596842283&rd=1
__________________
90 Honda CRX Si -Red/Black -B20B/b16 -AEM CAI -/\- Apexi GT Header/2¼" Custom Dynomax Exhaust -Tein SS CoilOvers with pillow ball monuts -/\- ST Swaybars/Energy Suspension Bushings -16x7 Lightweight Rotas -/\- Pro Stop Rotors -/\- Goodridge S.S. Brake Lines -Skunk2 Shifter -/\- MoMo Steering Wheel
|
|
#4
12-10-2005, 01:53 PM
|
|||
|
|||
|
Re: Crank pulley remover tool!!!!!!
$20 chain wrench at your local parts store
__________________
99 [email protected] psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me.
|
|
#5
12-10-2005, 02:27 PM
|
|||
|
|||
|
Re: Crank pulley remover tool!!!!!!
i just throw my impact gun on that center bolt, works everytime
|
|
#6
12-10-2005, 07:00 PM
|
||||
|
||||
|
3 ft breaker bar with a 3 foot pipie on that. Three sockets later you got it
__________________
91 Hatch SI Heart of my Baby - DOHC ZC - Si tranny - PG7 Finally painted!!!
|
|
#7
12-10-2005, 11:25 PM
|
||||
|
||||
|
Re: Crank pulley remover tool!!!!!!
3/4" $600 impact is funnest way.
|
|
#8
12-11-2005, 03:15 AM
|
|||
|
|||
|
Re: Crank pulley remover tool!!!!!!
800 ft lbs of torque and some nice lines on a 120 psi+ air compressor will do it.
__________________
99 [email protected] psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me.
|
|
#9
12-11-2005, 04:38 AM
|
|||
|
|||
|
Re: Crank pulley remover tool!!!!!!
with my impact gun rated at 450 ftlbs @90psi, it takes 120psi usually to crack that center bolt
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
