|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Fresh Beef Dog Food | IgorSushko.com | Corporate |
|
#1
11-28-2005, 10:49 PM
|
|||
|
|||
|
Almost there, push me over the top
Ok, so im just about done with gathering pieces for the 5lug swap. I have two front uprights from a 300zx with the hubs, spindles, everything on the way here. And im about to buy two rear hubs/spindles for the swap. My question is, when i do the swap, what other parts am i going to need, and will the S14 rotors work with the stock S13 calipers?
__________________
1988 conquest TSI -Lots of mods, finally finished WOOT!!  Horsepower sells cars, Torque wins races! 
|
|
#2
11-28-2005, 10:56 PM
|
||||
|
||||
|
Re: Almost there, push me over the top
USDM S14 rotors will work, for the rear all you need is the HUB and BEARING. For the front, i dunno.
|
|
#3
11-29-2005, 12:05 AM
|
|||
|
|||
|
Re: Almost there, push me over the top
yeap!
__________________
"A good driver is measured not by his lap times, but by the amount of time he spend trying to make sense of his car" E.K.
|
|
#4
11-29-2005, 01:24 AM
|
|||
|
|||
|
Re: Almost there, push me over the top
how hard is it to redrill stock S13 4lug rotors to the flug rotors? This would only be temporary if i did do it though...
__________________
1988 conquest TSI -Lots of mods, finally finished WOOT!! Horsepower sells cars, Torque wins races!
|
|
#6
11-29-2005, 04:48 PM
|
||||
|
||||
|
Re: Almost there, push me over the top
Take it to a machine shop.
|
|
#7
11-29-2005, 05:05 PM
|
||||
|
||||
|
Re: Almost there, push me over the top
I thought the 300zx front hubs wouldent work on a 240. I thought it had to be the 240 front hubs.
__________________
|
|
#8
11-29-2005, 05:39 PM
|
|||
|
|||
|
personally i would've just gone with something for like
pdm-racing and you are planning to redrill get a shop to do it you might not do properly if you dont know what you're doing and create some serious problems
|
|
#9
11-29-2005, 06:24 PM
|
|||
|
|||
|
Re: Almost there, push me over the top
Quote:
This is what you would have paid if you went with PDM for just hubs/wheel bearings. http://www.netstores.com/dwos-bin/proc_ordr.pl Money doesnt just grow on trees here. IM spending about 300$ doing it my way, rather than 1200$ for that...Big difference. And i will probably drill them my self, my father works at a machine shop and used to work part time there so im able to use whatever stuff i want. I just go in on the weekend when nobody is there.
__________________
1988 conquest TSI -Lots of mods, finally finished WOOT!! Horsepower sells cars, Torque wins races!
|
|
#10
11-29-2005, 07:00 PM
|
||||
|
||||
|
Re: Almost there, push me over the top
thats what it was like when i started doing mechanic it was awesome, but then my boss said he needs someone more experienced like a 3rd or 4th year not a 1st or 2nd.
__________________
Assad.. starting 180sx project soon  http://www.youtube.com/watch?v=aGRodKEfeZ4 <<<CHECK IT LOLL 
|
|
 |
POST REPLY TO THIS THREAD |
 |
|
|
