will this fit????
CRXsk8er
04-19-2003, 01:57 PM
does anyone kno if this carbon fiber hood will fit with a ZC engine????
it would help if i could kno cause i want to order this one if it will...thanks
it would help if i could kno cause i want to order this one if it will...thanks
doug294
04-19-2003, 02:16 PM
Hey that's my hood. I just got that hood on my car. I doubt it will clear your ZC though. It it barely clearing my D16.
mellowboy
04-19-2003, 03:32 PM
Get the cf hood with the zc bump.
CRXsk8er
04-19-2003, 07:26 PM
Originally posted by mellowboy
Get the cf hood with the zc bump.
yeah thats what i was thinking of but then again im goign to be gett and b16 or b18 in like two years and i would rather have that hood then the ZC hood but i guess i could sell it when i get the new engine that prolly what ill do.......thanks
Get the cf hood with the zc bump.
yeah thats what i was thinking of but then again im goign to be gett and b16 or b18 in like two years and i would rather have that hood then the ZC hood but i guess i could sell it when i get the new engine that prolly what ill do.......thanks
Kunundrum
04-19-2003, 07:31 PM
you can make it fit, I got my ZC to fit without taking the cam cover off, When the engine was put it it was shimmed down on the drives side using some 1/8" washers, and it fit fine.
since the motor is not in your car yet... you can do the same thing.
K-Drum
since the motor is not in your car yet... you can do the same thing.
K-Drum
CRXsk8er
04-19-2003, 08:04 PM
Originally posted by Kunundrum
you can make it fit, I got my ZC to fit without taking the cam cover off, When the engine was put it it was shimmed down on the drives side using some 1/8" washers, and it fit fine.
since the motor is not in your car yet... you can do the same thing.
K-Drum
i dont get where you would put the washers.........and how much lower would it make the cam cover cause that hood i think is lower then the stock one..........thanks
you can make it fit, I got my ZC to fit without taking the cam cover off, When the engine was put it it was shimmed down on the drives side using some 1/8" washers, and it fit fine.
since the motor is not in your car yet... you can do the same thing.
K-Drum
i dont get where you would put the washers.........and how much lower would it make the cam cover cause that hood i think is lower then the stock one..........thanks
Kunundrum
04-19-2003, 09:13 PM
here is a pic it should give you an idea, this is the drivers side motor mount.
CRXsk8er
04-19-2003, 09:38 PM
Originally posted by Kunundrum
here is a pic it should give you an idea, this is the drivers side motor mount.
k i get it now i just needed to look at the pic.......thanks......how much lower does that make you have any idea???and how many of them can i put in or will i like make sumthing not line up if i put like two.......thnaks
here is a pic it should give you an idea, this is the drivers side motor mount.
k i get it now i just needed to look at the pic.......thanks......how much lower does that make you have any idea???and how many of them can i put in or will i like make sumthing not line up if i put like two.......thnaks
Kunundrum
04-20-2003, 08:34 AM
i would not put more than 2 because it may trought the axel angle out of whack, so far 1 has not caused a problem, the nice thing is if too low or causes problems you can teke em out.
you can do one washer and take the timing cover off, that should give you the space you need for it to fit.
you can do one washer and take the timing cover off, that should give you the space you need for it to fit.
CRXsk8er
04-20-2003, 09:25 AM
Originally posted by Kunundrum
i would not put more than 2 because it may trought the axel angle out of whack, so far 1 has not caused a problem, the nice thing is if too low or causes problems you can teke em out.
you can do one washer and take the timing cover off, that should give you the space you need for it to fit.
that is just what i was think about a axels im not sure what im goign to do yet anyone out there have this hood with a ZC sawp???
i would not put more than 2 because it may trought the axel angle out of whack, so far 1 has not caused a problem, the nice thing is if too low or causes problems you can teke em out.
you can do one washer and take the timing cover off, that should give you the space you need for it to fit.
that is just what i was think about a axels im not sure what im goign to do yet anyone out there have this hood with a ZC sawp???
Automotive Network, Inc., Copyright ©2026