Guess what the next one is........The ENZO !!
primera man
02-21-2003, 10:36 AM
Originally posted by CalsonicR34
You use flat red for the seats or the red from the spray can ?
They have been brush painted in Tamiya XF-7 Flat Red
You use flat red for the seats or the red from the spray can ?
They have been brush painted in Tamiya XF-7 Flat Red
primera man
02-22-2003, 01:59 AM
Just adding a tip here for those that are going to be making this kit.
I'd that i'd share so no one else makes the same mistake.
The two intake bits that have the arrow on them....the edge has to be painted body colour.
I made the mistake of not painting this part correctly in the instruction's.
I already had it painted red then painted over the edge in black.:rolleyes:
You can see from the model pic it shows out when attached to the intakes and the rest of the car. I thought it would not be seen when assembled. :(
Hopefully can touch it up later
http://files.automotiveforums.com/uploads/290077Dscf0847A.jpg
http://files.automotiveforums.com/uploads/123283Dscf0835A.jpg
I'd that i'd share so no one else makes the same mistake.
The two intake bits that have the arrow on them....the edge has to be painted body colour.
I made the mistake of not painting this part correctly in the instruction's.
I already had it painted red then painted over the edge in black.:rolleyes:
You can see from the model pic it shows out when attached to the intakes and the rest of the car. I thought it would not be seen when assembled. :(
Hopefully can touch it up later
http://files.automotiveforums.com/uploads/290077Dscf0847A.jpg
http://files.automotiveforums.com/uploads/123283Dscf0835A.jpg
ales
02-22-2003, 02:01 AM
I think you should change the oil in the kiwi-bot more often! :D :finger:
j/k
Doesn't seem like a big deal that cannot be touched up. Good luck with it.
j/k
Doesn't seem like a big deal that cannot be touched up. Good luck with it.
rhmatt
02-25-2003, 09:10 AM
Three days with no update?!? I'm starting to get worried....
Yup, I still visit this site almost everyday...one day I'll find time to start building again! But for now I'll sit in the shadows and look on.
Keep up the awesome work P-man!
Yup, I still visit this site almost everyday...one day I'll find time to start building again! But for now I'll sit in the shadows and look on.
Keep up the awesome work P-man!
Vagabond_se7en
02-25-2003, 09:30 AM
Originally posted by rhmatt
Three days with no update?!? I'm starting to get worried....
Yup, I still visit this site almost everyday...one day I'll find time to start building again! But for now I'll sit in the shadows and look on.
Patience is a virtue :D :D
Been looking forward to see the Enzo completed too.
Jan
Three days with no update?!? I'm starting to get worried....
Yup, I still visit this site almost everyday...one day I'll find time to start building again! But for now I'll sit in the shadows and look on.
Patience is a virtue :D :D
Been looking forward to see the Enzo completed too.
Jan
RyanGiorgio
02-25-2003, 12:19 PM
Still coming along nicely. I can't wait to see the finished results.
fullbloodchop01
02-25-2003, 02:45 PM
when will this be fnished???????????? lol awsome job as always pman:p
primera man
02-25-2003, 03:21 PM
I thought i may have got it finished in the weekend but other things came up :mad:
The car has been polished and looking alot better now. The widow trim is drying at the moment which was the last bit of painting i needed to do.
Hasn't been touched for a few days before that as i've been pretty busy trying to get my car (1:1) ready for the 4's&Rotary Nationals at the end of March :cool: :cool:
But hopefully it will get done in the next few days all going well :)
The car has been polished and looking alot better now. The widow trim is drying at the moment which was the last bit of painting i needed to do.
Hasn't been touched for a few days before that as i've been pretty busy trying to get my car (1:1) ready for the 4's&Rotary Nationals at the end of March :cool: :cool:
But hopefully it will get done in the next few days all going well :)
primera man
02-26-2003, 06:12 PM
Quick update :)
All panels are now polished and been test fitting them today to see what they are like. They all fit really well and its starting to take shape now :devil:
Should be all done soon :flash:
All panels are now polished and been test fitting them today to see what they are like. They all fit really well and its starting to take shape now :devil:
Should be all done soon :flash:
Integra14
02-26-2003, 07:03 PM
wow.. is the only word to describe
SuPeRcAr_MaN
02-26-2003, 07:49 PM
Originally posted by Integra14
wow.. is the only word to describe
Ditto. Just "wow". :eek:
wow.. is the only word to describe
Ditto. Just "wow". :eek:
slim.AP1
02-26-2003, 07:50 PM
*mmm* delicious
Ghost_9418
02-26-2003, 07:54 PM
That it is unbelievable:D Great work
COZMO6476
02-26-2003, 08:23 PM
tight like a tiger!
zangief
02-26-2003, 08:44 PM
looks good.....
is that a 1/4 mile track ur getting ur 1:1 CAR READY FOR?
is that a 1/4 mile track ur getting ur 1:1 CAR READY FOR?
Hiroboy
02-26-2003, 11:56 PM
This is really starting to take shape now, the shine is awesome. Can't wait to see the complete job, with loads of photos.
chaos
02-27-2003, 12:16 AM
As with all P'man's models...words defy me!
primera man
02-28-2003, 12:42 AM
Just another tip to look out for.
The rear body panel does not sit down far enough and needed to be glued and 'rubber-banded" in place to dry.
I must say i was quite supprised by the bad fit....i'll be interested to see when others build this kit to see what it's like.
The bits shown is where it does not sit down far enough onto the bottom skid panel....there would be about a 1-2mm gap.
I have used Kristal Klear glue which takes longer to dry but wont melt the paint incase i screwed it up.
Hopefully it works out OK
http://files.automotiveforums.com/uploads/836086Dscf0902.jpg
http://files.automotiveforums.com/uploads/217549Dscf0907.jpg
The rear body panel does not sit down far enough and needed to be glued and 'rubber-banded" in place to dry.
I must say i was quite supprised by the bad fit....i'll be interested to see when others build this kit to see what it's like.
The bits shown is where it does not sit down far enough onto the bottom skid panel....there would be about a 1-2mm gap.
I have used Kristal Klear glue which takes longer to dry but wont melt the paint incase i screwed it up.
Hopefully it works out OK
http://files.automotiveforums.com/uploads/836086Dscf0902.jpg
http://files.automotiveforums.com/uploads/217549Dscf0907.jpg
endlesskev86
02-28-2003, 01:01 AM
looks good P-man!! as usual
xim-crow
02-28-2003, 02:51 AM
Originally posted by endlesskev86
looks good P-man!! as usual
Hey Endlesskev86, stop showing us your pretty girlfriend, I can't concentrate myself any more on the Enzo of Pman
PS : could you lend her to me for a while ?!!:D :sun: :silly2:
looks good P-man!! as usual
Hey Endlesskev86, stop showing us your pretty girlfriend, I can't concentrate myself any more on the Enzo of Pman
PS : could you lend her to me for a while ?!!:D :sun: :silly2:
BBCivic
02-28-2003, 03:53 AM
:eek2: Like usual, Excellent work...
:sun: :sun: :sun:
:sun: :sun: :sun:
Purpura Delujo
02-28-2003, 05:03 AM
Looks great for a red Enzo Pman ( :finger: ), that mistake with the air intake will teach you for not painting it black, then it wouldn't of shown up.......:D
ultraxduce
02-28-2003, 05:30 AM
what do you get when you..
get the post popular model (these days) and the most popular modeler?
a thread thats been viewed more than half the FAQ..
get the post popular model (these days) and the most popular modeler?
a thread thats been viewed more than half the FAQ..
Forhod
02-28-2003, 05:36 AM
Pman, nice work! Hope to see it soon :D
Who is the creator of the thread? Pman :D
His work is popular here, so the views and replies are high. :cool:
*Forhod looks at the pages.. :eek:
Who is the creator of the thread? Pman :D
His work is popular here, so the views and replies are high. :cool:
*Forhod looks at the pages.. :eek:
bigfrit
02-28-2003, 09:43 AM
:D DROOL :eek:
primera man
02-28-2003, 12:10 PM
Originally posted by ultraxduce
what do you get when you..
get the post popular model (these days) and the most popular modeler?
a thread thats been viewed more than half the FAQ..
Everyone that has viewed the thread sends me $10 each :p :p
Anyway.....cut the rubber band off after 12 hours drying and it has stayed together :cool:
what do you get when you..
get the post popular model (these days) and the most popular modeler?
a thread thats been viewed more than half the FAQ..
Everyone that has viewed the thread sends me $10 each :p :p
Anyway.....cut the rubber band off after 12 hours drying and it has stayed together :cool:
bvia
03-01-2003, 10:00 PM
Originally posted by primera man
Everyone that has viewed the thread sends me $10 each :p :p
WHY?...are you starting a "mast fund" for the Black Boat?...;-)>
Bill
:bandit:
p.s. once again a beautiful build, showing that even the artists of our hobby must deal with frustrations and push work through them!
Everyone that has viewed the thread sends me $10 each :p :p
WHY?...are you starting a "mast fund" for the Black Boat?...;-)>
Bill
:bandit:
p.s. once again a beautiful build, showing that even the artists of our hobby must deal with frustrations and push work through them!
MX100
03-01-2003, 11:33 PM
very nice lookin ENZO!!! amazing.
:)
Hey Endlesskev86, stop showing us your pretty girlfriend, I can't concentrate myself any more on the Enzo of Pman
ya kev~ jeez~ stop bringing her out with us when we go out for a drink~ I am so jelous....:finger: :flipa: :finger: :flipa:
:)
Hey Endlesskev86, stop showing us your pretty girlfriend, I can't concentrate myself any more on the Enzo of Pman
ya kev~ jeez~ stop bringing her out with us when we go out for a drink~ I am so jelous....:finger: :flipa: :finger: :flipa:
beginner
11-25-2003, 01:57 AM
They are long tooth picks that are just taped to a piece ot the "tree" so i can hold on to them when i spray.
I cut as much off as i can before painting. Try and leave each piece holding on by just one strong bit from the sprue
But what do you do after you have sprayed the pieces? I mean when you cut the piece from the tree, won't there be a spot that's missing paint? How do you fix that? Brush?
I cut as much off as i can before painting. Try and leave each piece holding on by just one strong bit from the sprue
But what do you do after you have sprayed the pieces? I mean when you cut the piece from the tree, won't there be a spot that's missing paint? How do you fix that? Brush?
Automotive Network, Inc., Copyright ©2025