Which other cars has this Engine??

What year and kind of car has a 1.8 DOHC that will bolt into a 91 Honda Civic Si after a few mods?

Thanks

the 1.8 DOHC engine comes out of a 1990-2000 integra. 90-91 is B18A and has 130hp but comes with cable tranny. 92-93 is B18B with 140hp and comes also with cable tranny. when u get to 94-95 it is no longer non-obd wireing like 90-93. 94-95 is obd-I and 96-2000 is obd-II.
All of these engies are B series so u would need a new set of engine mounts to accomadate your D series engine bay. The easiest swap would be the b18a, less wireing.

AC

-88 dx with 89 JDM integra XSI engine tranny(Limited Slip Differential) ecu, Iceman intake, hiflow cat, apexi n1 muffler with 2 1/4 " piping,

actually all 90-93 Are B18A's, its just the 90-91 is OBD0 and the 92-93 is OBDI. the 94-01 However is the B18B1. If you are wanting to swap one in, i would recommend the 90-91 OBD0 B18A, that way you wont have to deal with any wiring.

Ok so the years 90-93 Integra are the best to go with?? There is no other cars with this engine?? Would it be much more difficult to go with the B18B?? What else would I need besides mounts and linkages??

Thanks

yea 90-93 will work, but i think 90-91 will work better since its OBD0. The B18B would be ok, but you will have to wire it from OBDI to OBD0 or from OBD2 to OBDI, but then you would have to get the whole car wired for OBDI, if you went with an OBD2 motor. You would also have to get a cable tranny, since all B18B's come with hydrolic. You will just need the mounts and a new shift linkage otherwise. If you have any more ?'s, just ask.

-Bryan

Ok so stick with 90-91 and than I just need the mounts and a new shift linkage nothing more?? Do you know of any cheep places to get mounts and linkages?
Thanks

www.hasport.com has the mounts. You might have to make your own custom shift linkage or look on www.ebay.com for all that stuff.

Ok thanks for the help guys!! Any idea what a 91 Civic Si 1.6 SOHC engine an 5spd tranny worth with 171,000Km on it?
Thanks

my advice.. get a 90-91 B18A1, swap a newer head on it, and you have more power. the 90-91's had shafty cams and a crappy flowing head.

won't he need the teg axles too?

What are teg axles??

teg = short hand for integra

Well I'm getting the whole car so I can use them too. They will fit right?? Thanks for pointing that out though!!

Well I'm getting the whole car so I can use them too. They will fit right?? Thanks for pointing that out though!!

they will fit once you take the dust caps off of your front knuckles. if you leave them on, you prolly will still be able to make the CV shafts fit, but you might get binding and you dont wanna kill the wheel bearings.

screw it....get a b-20 2.0 liters of tourquie goodness :D

If you do the swap get some 94-97 cams to replace the 90-91 cams. they have a lil more lift and will give you a lil more umph. good luck on the swap the ls is my favorite engine too :iceslolan

screw it....get a b-20 2.0 liters of tourquie goodness :D

Man, my friends b18a1 killed a guys stripped down 1990 model prelude with a b20 in it, the b20 has more off the line but after that the b18 kills it.

the old school 'ludes have a totally different engines that that found in the honda crv....the oldschool lude's engine doesnt even earn the name b20

If I had a 92 civic rather than a 91 civic will i need to worry about wiring, mounts,or linkages if I went with a 92-93 acura entegra engine?? Does it matter if the civic is Si or not??
Thanks