Program keyless remote-Need instructions

Hey I need some help I have a 2006 corolla and when i lock tthe doors the car won't beep or when i unlock it and it used to befor i had my ecureplaced if anyone knows how to reprogram it so it will beep plaese let me know or if it is something i have to take to the dealership thanks

Hello everyone;

I just bought a 2001 4Runner LTD. It came with only one remote & I'd like to buy an additional one. I was checking listings on ebay & some come with programming instructions and some do not. Don't totally trust their claims & would feel better if I had instructions from another source.

My remote has 3 buttons on the front (lock, unlock & rear window) with a red panic button on the back. The FCC ID # is HYQ1512Y.

Thanks in advance for any all help.:wink:

I have lost the only keyless remote for my 2004 4Runner. I thought I had the number from the back written dow. Is there another way to buy a remote without the number?

Norman Kipp
[email protected]

Hello, I need help with the programming of my keyless remote. I have a '99 4runner limited and have tried a couple of the instructions from here, but they don't seem to work. Can anyone help. Thanks!

what about a 2001 dodge dakota? anyone know how to program for that? please and thank you.

To Program A Rs3000 Toyota Alarm For Corolla 98-00.

1 - Put The The Key In The Ignition "on" Position With Only The Driver's Door Open.
2 - Reach The Rs3000 Module Under The Driver's Seat.
3 - Press And Hold For 5 Seconds The Little Green Button On Left Side Of The Module (side Door), Until The Alarm's Led Stay Without Flashing.
4 - Press Any Button On The Remote For 1 Sec.
5 - When You Hear The Beep And See The Lights Flashing, Take The Key Out Of The Ignition.
6 - Enjoy Your Alarm.

Please Feel Free To Ask Any Question.
Also Have Keyless Instalation 4 Elantra And Mitsubishi.
Good Luck!!!!!!

[/quote]

[/quote]

I had a question :rolleyes: where exactly is the green button? I looked underneath the car but there is the hole and in that hole there is this yellow plastic thing that have bunch of wires in it running left and right. Please tell me where I can find the green button?:runaround: :confused:

I'm really can't find the green button under the driver seat. :banghead:

Please can you tell me where specifically underneath the driver seat on a Toyota Corolla 98-01.:rolleyes:

I need help. I just bought a 2000 4 runner and dont know if it is keyless. How would I find out befor I buy a keyless remote? Thanks Dave

Depends on which remote system you have.

Factory or DEALER/PORT installed? (RS3000)

Hello! I am so confused... i have a '98 Camry and have been using a BAB237131-022 keyless remote for about two years. It suddenly stopped working so I assumed it was the battery and bought a new one from an auto parts store. I can't figure out how to program it, and the dealer wants $50 to do so- any ideas??

I need the programing instructions for a 1997 Toyota 4Runner. Will these work or something different????

Hi all,

I just purchased a 2000 RAV4 for my son, it has power locks and windows. Previous owner did not have a keyless remote. How can I find out if his car has that option and if so can I buy an after market remote on eBay? I would greatly appreciate an email response [email protected] Thanks!

instructions worked (after some practice) for a 2005 Camry XLE

thanx a LOT for the post!!! was able to save some for really needed parts.

I have genuine TOYOTA remotes, and I am trying to programm one of them for 03 4runner LTD. Can any one help with instructions please!

Does anyone know what it means if while programming the horn goes off but the locks don't cycle?

Thank you

I have an 01 4Runner SR5 with the Karr alarm/keyless. I tried the lock/unlock 5 times, close open door, and lock/unlock 5 more times, etc. I got into the programming mode (I think). It cycled lock/unlock by itself. I pushed the buttons on the remote, then the lock by itself. I get the lock/unlock twice meaning it didn't take.

I tried the whole procedure again and I can't get it to the programming mode again. Is there something else? Is my system locked out for adding another remote. I have 2 that I'm aware of.

Thanks.

please help i need to find the programing info for my 1996 corolla with the vip s1000 system istalled

[quote=daffy_duck-010;1723940]The dealer was happy to give it to me so here is the procedure. let me know if it works. (Camry 02 and 03)

1. Driver door open and unlocked. Key out of the ignition
2. Insert the key and remove 2 times in 5 sec.
3. Close and open driver door 2 times in 40 sec.
4. Insert the key and remove it again from ignition.
5. Close and open driver door 2 times in 40 sec.
6. Insert the key in ignition,
7. Close the door,
8. Turn to on and back to lock in 1 second intervals. 1 time for add, 2 times for rewrite, 3 for confirmation 5 for prohibition. (yes, there is no “4”)
9. Remove the key
10. Power lock will cycle to confirm
11. For add or rewrite mode within 40 sec of the confirmation,
A. press “lock” and “unlock” buttons of the FOB at the same time between 1 and 1.5 seconds.
B. within 3 sec press “Lock” button for more than 1 sec and release.
C. If it’s correct, the power door lock will cycle once. If it’s wrong the door lock will cycle twice.


i already tried this procedures on my Prado 2004 and believe me it work so keep trying :-)

Can anyone provide programming instructions for a used keyless remote fob I will be buying, to work with a Toyota Landcruiser Colorado (1997 model)...:smile:

Land Cruiser "Colorado" is a non-US type. The 95-97 LC all use the same programming type.

Direct Link - http://originalkeyless.com/1995-Toyota-Land-Cruiser-Keyless-Entry-Remote-95-FJ80-FZJ80-SUV-95-Land-Cruiser-TVSS-Remote.htm?categoryId=-1

Press and hold the green programming button on the side of the control unit with a pen or pencil until the exterior lights come on. The lights will come on for five seconds. (next steps must be done within 5 seconds of each other.)
Press and release the top button on the transmitter.
Check that the LED goes out, the siren chirps once, and the front marker lights flash to confirm that the transmitter's code was accepted by the control unit.
If you have other transmitters to program, repeat that step for each one.

(Common location for receiver is under the driver's seat)

http://originalkeyless.com/images/1175746587464-1277053796.jpeg

Program keyless remote
I'm really can't find the green button under the driver seat. :banghead:

Please can you tell me where specifically underneath the driver seat on a Toyota Corolla 98-01.:rolleyes:

My 1998 Corolla did not have a green button. It was a recessed button on the side closest to the driver's door. There shouldn't be a problem since there is only one button on that side. The directions posted worked for me. Thanks.

DESPERATE!

Hi I have a 1999 Runner SR5 with the VIP RS3000 facory installed alarm. I purchased the HYQ1512Y alarm remote from Ebay and I am tryign to program.

I have followed the instructions that came with it and the one posted on this board. I can get into the programming mode, but I cannot add the remote. I keep getting the locks to cycle twice(unsuccessful) instead of once (successful) when I hold either the lock or unlock button for 2 seconds.

When I insert the key into the ignition, do I have to turn the key once, twice, three times, or ultimately 5 times? I am getting frustrated?!?!?!

Thanks in advance to all.

JS

Theres your problem right there.

The RS3000/VIP remote system is DEALER/PORT installed.

Your FCC: HYQ1512Y remote is for a FACTORY installed system.

The remote you need is FCC: BAB237131-022 which would have originally been the GRAY case type, but you can also use the BLACK case type of the 96-97 models.

(that interchangeability only works one way, a 96-97 model MUST use BLACK case and cannot use Gray).

Theres your problem right there.

The RS3000/VIP remote system is DEALER/PORT installed.

Your FCC: HYQ1512Y remote is for a FACTORY installed system.

The remote you need is FCC: BAB237131-022 which would have originally been the GRAY case type, but you can also use the BLACK case type of the 96-97 models.

(that interchangeability only works one way, a 96-97 model MUST use BLACK case and cannot use Gray).

Thanks.....but i noticed that the BAB237131-022 has only TWO buttons(lock, unlock) on the front. My original key FOB had three (Lock, Unlock, rear window). So maybe its not the VIP RS3000? Very confused now

If your original remote had the rear window type, then it IS the Factory system.

The remote should be FCC: HYQ1512Y, but if you are getting into programming mode and the vehicle responds, but the remote will not respond - the remote may need the batteries replaced or could be defective.


****Make sure you are not pressing the brake pedal at all during the procedure as it will interfere with programming mode.
*
*** Also, some customers report success programming with the driver's door open - where others report success with all doors closed.

IMPORTANT: If the procedure calls for turning or inserting and removing the key in the ignition, this is time sensitive. Try speeding up or slowing down your pace on this step.

If your original remote had the rear window type, then it IS the Factory system.

The remote should be FCC: HYQ1512Y, but if you are getting into programming mode and the vehicle responds, but the remote will not respond - the remote may need the batteries replaced or could be defective.


****Make sure you are not pressing the brake pedal at all during the procedure as it will interfere with programming mode.
*
*** Also, some customers report success programming with the driver's door open - where others report success with all doors closed.


IMPORTANT: If the procedure calls for turning or inserting and removing the key in the ignition, this is time sensitive. Try speeding up or slowing down your pace on this step.

I assuming the remote is repsonding since the locks are cycling, but twice. I will try your suggestions. Thanks for your help!!
:smokin::runaround::crying:

If your original remote had the rear window type, then it IS the Factory system.

The remote should be FCC: HYQ1512Y, but if you are getting into programming mode and the vehicle responds, but the remote will not respond - the remote may need the batteries replaced or could be defective.


****Make sure you are not pressing the brake pedal at all during the procedure as it will interfere with programming mode.
*
*** Also, some customers report success programming with the driver's door open - where others report success with all doors closed.

IMPORTANT: If the procedure calls for turning or inserting and removing the key in the ignition, this is time sensitive. Try speeding up or slowing down your pace on this step.

One thing i forgot to mention is that the hyq1512y remote i purchased online has a picture of a car with trunk open instead of the rear glass window on the third remote button.

Are there 2 hyq1512y remotes out there? I thought the FCC ID # was the most important thing?

HYQ1512Y with the SUV window button is from the 1999-2002 4Runner.

HYQ1512Y with the trunk button is from the 1998-1999 Avalon.

See here:

http://originalkeyless.com/searchquick-submit.sc?keywords=hyq1512y

I have my girlfiends 1995 toyota avalon got a new remote but dont know how to program it. Lots of other blogs but what is the correct way I dont want to brake something. I hope some one can help me. Thanks

This is a factory keyless. Red led next to temp and clock display

95 Avalon with FCC: GQ43VT7T on back of remote:


1. Remove key from ignition
2. Locate bulb failure warning module in trunk near left trunk
hinge and disconnect electrical connector.
3. Jump pins 12 (black) to 11 (black/white) of connector with short wire or paper clip
4. Door locks will cycle
5. Press any button on remote keyless entry entry transmitter
6. Door locks will cycle
7. Repeat steps 5 & 6 for another transmitter
8. Remove jumper from connector and reconnect to module


NOTE: Entering programming mode erases all previously
programmed transmitters.