Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Let's get Technical! Discussion for hardcore in-depth motor heads! |
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
11-15-2005, 07:50 PM | #1 | |
AF Enthusiast
Join Date: Dec 2002
Posts: 588
Thanks: 0
Thanked 0 Times in 0 Posts
|
torque specs... help
i need torque specs for the following things
b16a motor head bolt specs |
|
11-15-2005, 07:54 PM | #2 | |
AF Enthusiast
|
Re: torque specs... help
The first b16a motor has 111lb/ft@7000rpm
|
|
11-15-2005, 09:24 PM | #3 | |
AF Enthusiast
|
Re: torque specs... help
What year/make/model/engine/etc.... Different years and makes have been known to have different specifications. You did mean torque specs, not engine torque output, right?
|
|
11-15-2005, 09:39 PM | #4 | |
AF Enthusiast
Thread starter
Join Date: Dec 2002
Posts: 588
Thanks: 0
Thanked 0 Times in 0 Posts
|
yea lol.. torque specs... for the head bolts
92 b16a |
|
11-15-2005, 09:48 PM | #5 | |
AF Enthusiast
|
Re: torque specs... help
These require 2 settings:
First setting: 22 ft. lbs. Second Setting: 61 ft. lbs. |
|
11-16-2005, 02:09 PM | #6 | |
AF Enthusiast
Thread starter
Join Date: Dec 2002
Posts: 588
Thanks: 0
Thanked 0 Times in 0 Posts
|
also need torque specs for the cam caps...
|
|
11-16-2005, 03:30 PM | #7 | |
AF Enthusiast
|
Re: torque specs... help
#
Tighten the camshaft holder bolts for 1984-91 to 16 ft. lbs. (22 Nm). For 1992-95 engines tighten to the following specifications: 8mm bolts: D16Z6, D15Z1 engines: 14 ft. lbs. (20 Nm) D15B7, D15B8 engines: 16 ft. lbs. (22 Nm) 6mm bolts: All engines: 9 ft. lbs. (12 Nm) |
|
11-16-2005, 03:48 PM | #8 | |
AF Enthusiast
Thread starter
Join Date: Dec 2002
Posts: 588
Thanks: 0
Thanked 0 Times in 0 Posts
|
i have a b16a 92 motor... dohc vtec
also how do i tighten the timing belt... i can't get it to tigthen correctly.. 1 side is tight the other is loose... |
|
11-16-2005, 03:57 PM | #9 | |
AF Enthusiast
|
Re: torque specs... help
I'm having a hard time finding a procedure. What model honda did your engine come from?
|
|
11-16-2005, 05:29 PM | #10 | |
AF Enthusiast
Thread starter
Join Date: Dec 2002
Posts: 588
Thanks: 0
Thanked 0 Times in 0 Posts
|
not sure i think the 92-95 sir hatch b16a
|
|
11-16-2005, 05:44 PM | #11 | ||
AF - Advisor
Join Date: May 2003
Location: too damn far., California
Posts: 3,039
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Re: torque specs... help
Quote:
9 5 1 3 7 8 4 2 6 10 as for specific years someone was refering to up there. the b18c5, b16, b18a/b, and b18c5 all have the same specs. the crankshaft and camgears need to be at TDC with the belt on. to properly tension, rotate the camgears three teeths apart then tighten the tensioner. the belt tension between the two camgears should be tight. the tension between the ctankshaft and exhaust camgear should be no more than an 1 inch deflection.
__________________
99 JRSC@9.5 psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me. |
||
11-17-2005, 12:03 AM | #12 | |
AF Enthusiast
Thread starter
Join Date: Dec 2002
Posts: 588
Thanks: 0
Thanked 0 Times in 0 Posts
|
after i put on the cam caps... i cannot turn the cams i try turning them with a rachet but they wont turn... did i do sumthing wrong..?
also how do i set the timing rite..? do the cam gears have to be a certain way??? also wat is the valve adjustment specs..?a |
|
11-17-2005, 09:36 PM | #13 | |
AF Enthusiast
|
Re: torque specs... help
I'd say your cam caps are over tightened, bad.
|
|
11-17-2005, 10:01 PM | #14 | |
AF Enthusiast
|
Re: torque specs... help
|
|
11-17-2005, 10:03 PM | #15 | |
AF Enthusiast
|
Re: torque specs... help
I can't even find anything on timing belt procedures....
|
|
|
POST REPLY TO THIS THREAD |
|
|