Blackcrow64's Talon TSi AWD Project Progress Thread... (SOLD) - Page 15

MazdaX · 07-23-2007, 08:23 AM

Quote:

Originally Posted by Blackcrow64

All I could find on there was complete axle sets... I talked to my buddy at the dealership here and I cannot get just the axle boot like I need from Mitsu... So I don't even have a part number or anything to go by... Mike posted up links to those axle boots, but they all appear to be the same and I donno which one I need to order... I'm hoping he gets online sometime tonight or tomorrow morning and can tell me which one I need specifically...

Well I just happened to be strolling through pep boys the other day to pick up some royal purple and I walked down the aisle where they have that 'HELP' type stuff and to my lower left at the end I noticed they had a massive pile of CV boots for individual sale. So if you have a local pep boys , you could go look there ? and save yourself the hassle of internet matching or searching if they have them.

Blackcrow64 · 07-23-2007, 01:40 PM

Quote:

Originally Posted by MazdaX

Well I just happened to be strolling through pep boys the other day to pick u some royal purple and I walked down the aislewhere they have that 'HELP' type stuff and to my lower left at the end I noticed they had a massive pile of CV boots for individual sale. So if you have a local pep boys , you could go look there ? and save yourself the hassle of internet matching or searching if they have them.

Sweet... I may have to go take a look up there one of these days this week... We have one about an hour away from me. lol

Thanks for the tip man.

Blackcrow64 · 07-31-2007, 06:29 AM

Just an update...

Ordered a shit ton of parts last night in hopes if finishing it up for the most part... Once I get the parts in this week all I will have left to do is my IC pipes and exhaust...

Oh and replace that damn sending unit top still...

I also killed the Firebird today, I think...

spyderturbo007 · 07-31-2007, 08:16 AM

Holy crap, you are hard on cars. Remind me not to let you drive the Spyder.

Blackcrow64 · 07-31-2007, 02:35 PM

Quote:

Originally Posted by spyderturbo007

Holy crap, you are hard on cars. Remind me not to let you drive the Spyder.

lol How do you figure I'm hard on cars? It's not my fault it died this morning...

baritonejim · 07-31-2007, 09:10 PM

How do you get to the ignition coil inside the Mitsubishi distributer, do you have to drive out the pin that holds the gear, or do you have to tueb the screw in the center of the rotor socket. Does this screw screw backwards?

Blackcrow64 · 08-01-2007, 02:05 AM

Quote:

Originally Posted by baritonejim

How do you get to the ignition coil inside the Mitsubishi distributer, do you have to drive out the pin that holds the gear, or do you have to tueb the screw in the center of the rotor socket. Does this screw screw backwards?

What the heck are you talking about? There are no distributors and rotors on these motors. They use coil packs...

Like this...

And what does that have to do with anything in here anyways?

Mikelb · 08-01-2007, 09:10 AM

He must have a 1G SOHC... and Blackcrow is right, WTH did that have to do with anything...

Blackcrow64 · 08-02-2007, 05:42 PM

Thought you guys might like to see a few pictures of what I just got in the mail...

Got my 10mm Magnecor's, Flanges for my turbo and header, v-band for my downpipe, an awesome mount for my coil pack, turbo feed and return lines, a few harnesses, and my belts...

The mount for the coil pack was pretty sweet I thought, and I wasn't sure where to mount it so I thought; sure why not... It is a nice pieces, but I thought the welds coulda been a little nicer...

The look decent here...

But then you look on the penetration side and theres all these nasty lookin goobers... I might try to clean them up a bit so it doesn't look so bad and then polish the piece...

Anywho... Now all I gotta do is hunt down a good sending unit top since the fuel line snapped off of mine and I'll be very close to start up...

Blackcrow64 · 08-02-2007, 07:49 PM

Shit... The flanges don't match up to my turbo...

More wait time...

eclipsed at 3am · 08-07-2007, 10:55 PM

Quote:

Originally Posted by Blackcrow64

Shit... The flanges don't match up to my turbo...

More wait time...

that sucks bro lol...sorry to hear that. well you've been working on this car for so long, a few weeks or so shouldnt be too bad.

ive been following this thread along since you first posted, reading all the progress. i actually had a dream a few nights ago where I was completely rebuilding MY eclipse. 6 bolt motor, turbo, all these parts in the mail and everything, and the thing crankwalked BAD lol. hopefully that doesnt happen, well it shouldnt with the motor you got. i hope everything goes well. dont get TOO caught up with the car when you get it running and remember to keep us posted!

xavier3jr · 08-22-2007, 01:01 PM

Come on u slow pos.......:-D i wana see this thing running and soon!

Blackcrow64 · 08-22-2007, 01:44 PM

Still waiting on extremepsi to send me the right flanges so I can get it finished up...

goldz28 · 09-06-2007, 01:28 PM

Is this thing done yet?????????

steviek · 09-06-2007, 01:36 PM

Quote:

Originally Posted by goldz28

Is this thing done yet?????????

lol should i answer that

Thread Thread Starter Forum Replies Last Post

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Thor's Car Progress Thread: '90 TSI AWD project, parts cars, and the Cavy. 56k death!	Thor06	Members Projects	45	10-28-2008 03:26 PM
FS: 1992 Eagle Talon TSi AWD 5 speed	mahanian	Off-Topic	0	02-04-2003 05:08 PM
Eclipse GSX VS TALON TSI AWD	Platinum_Skyline01	Off-Topic	4	10-15-2002 02:49 PM
FOR SALE! 92 talon tsi awd 5 speed	brads94accord	Off-Topic	0	06-27-2002 01:50 PM
'93 Eagle Talon Tsi AWD Turbo A/T	Andre the Giant	Off-Topic	0	12-21-2001 01:40 PM

POST REPLY TO THIS THREAD