Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
08-13-2002, 05:10 PM | #1 | |
AF Newbie
Join Date: Jul 2002
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Reprogramming Keyless Entry - '98 LeSabre
1998 Buick LeSabre Keyless Entry Programming
ALL TRANSMITTERS MUST BE PRESENT WHEN PROGRAMMING NEW REMOTES! 1. Turn OFF ignition switch. 2. Use a 3 amp fused jumper wire (two clip leads attached to either side of a 3 amp fuse and paperclips work, too) and connect terminals at the data link connector as illustrated below (black wire to black/white wire). The data link connector is located on the driver's side bottom of dash panel. (See picture) 3. Close all the doors. 4. Turn ON the ignition switch. 5. The doors will lock and unlock to confirm it is in programming mode. 6. Press and hold LOCK and UNLOCK on one of the transmitters for 30 seconds. 7. After a 10-15 second delay the doors will LOCK and UNLOCK. DO NOT TURN OFF THE IGNITION! 8. Repeat step 5 for each additional transmitter. (Even transmitters that worked previously must be reprogrammed). 9. Disconnect jumper wire from data link connector. 10.Turn the ignition off and test all transmitters to verify function. |
|
08-14-2002, 05:32 PM | #2 | |
AF Newbie
Join Date: Dec 2001
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
I had posted the question about the '98 LaSabre way back when. Went to purchase a remote and was told at the dealership t hat the 98 LaSabre I brought in was not set up for it. LThanks
|
|
02-23-2003, 09:30 AM | #3 | |
Banned
Join Date: Feb 2003
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
reprogramming for 01 buick lesabre
Will this same procedure work for the 01 Lesabre?
Thanks |
|
07-13-2003, 10:56 PM | #4 | |
Pimpin' ain't easy
|
I am stickying this to the top of the page, and editing your thread title, if you don't mind
[Edit- had a better idea]
__________________
|
|
01-17-2007, 08:31 AM | #5 | |
AF Newbie
Join Date: Dec 2006
Location: Benton, Arkansas
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: How to- Reprogramming Keyless Entry - '98 LeSabre
2. Use a 3 amp fused jumper wire (two clip leads attached to either side of a 3 amp fuse and paperclips work, too) and connect terminals at the data link connector as illustrated below (black wire to black/white wire). The data link connector is located on the driver's side bottom of dash panel. (See picture)
Where is the illustration and picture? Another post in this board said for a '98 LeSabre to short wires 4 and 8 on the DLC. I have a '98 LeSabre, and in the DLC, there is no wire on the 8th terminal. |
|
01-17-2007, 08:44 AM | #6 | |
AF Moderator Elite
Join Date: Feb 2005
Location: Gilligan's Island, Florida
Posts: 5,762
Thanks: 83
Thanked 72 Times in 72 Posts
|
Re: How to- Reprogramming Keyless Entry - '98 LeSabre
Welcome to AF!
This thread is 6 1/2 years old and pictures can be lost from the original source over extended periods of time. You need to Post A New Thread with your questions. Please Read: Posting in closed or outdated threads
__________________
Knowledge can be communicated, but not wisdom! |
|
|
POST REPLY TO THIS THREAD |
|
|