Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Engineering/Technical
Engineering/Technical Ask technical questions about cars. Do you know how a car engine works?
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 04-29-2023, 08:57 PM   #1
ducked
AF Newbie
 
Join Date: Sep 2022
Location: Tainan
Posts: 55
Thanks: 0
Thanked 0 Times in 0 Posts
Cylinder Wall Pre-Ignition Damage?

Damage to cylinder #2 wall. Zooming in to the photo, it looks like lots of superimposed little impact marks rather than a scratch.

forumosauploads-12829.kxcdn.com/original/3X/1/c/1c...g

https://forumosauploads-12829.kxcdn....2_666x500.jpeg

My best guess was broken end of a piston ring dancing around, but I have now taken the piston out and so far can't see anything wrong with it or the rings.

I'll clean it up, check the ring gaps, and maybe smooth off the ends a bit, though I can't see any burrs.

Havn't decided whether to hone the cylinder yet. Probably not.

I suppose this damage could have been from a hard object that has since departed

Alternatively, could it be detonation or pre-ignition forcing impact of the ring ends onto the cylinder wall?

(The top ring gap was probably roughly in the right orientation on removal)

When I first got the car it seemed to have some pre-ignition on idle and had some run-on after switch off, both of which went away after a water decoke.

Last edited by ducked; 04-29-2023 at 09:00 PM. Reason: link truncated
ducked is offline   Reply With Quote
Old 04-29-2023, 10:03 PM   #2
maxwedge
A990 racer
 
Join Date: Mar 2002
Location: Chestertown, New York
Posts: 16,942
Thanks: 25
Thanked 369 Times in 363 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Detonation would be most obvious around the top edge of the piston above the top ring land. Looks like foreign material scrubbed the wall, that should be cleaned up.
__________________
maxwedge is offline   Reply With Quote
Old 04-30-2023, 01:06 AM   #3
ducked
AF Newbie
Thread starter
 
Join Date: Sep 2022
Location: Tainan
Posts: 55
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Quote:
Originally Posted by maxwedge View Post
Detonation would be most obvious around the top edge of the piston above the top ring land. Looks like foreign material scrubbed the wall, that should be cleaned up.
Think I had pre-ignition rather than detonation, though I canít be sure. Was shortly after I got the car, getting on for 10 years ago.

By ďthat should be cleaned upĒ you mean the cylinder should be honed?
ducked is offline   Reply With Quote
Old 04-30-2023, 08:01 AM   #4
maxwedge
A990 racer
 
Join Date: Mar 2002
Location: Chestertown, New York
Posts: 16,942
Thanks: 25
Thanked 369 Times in 363 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Yes a lite hone to clean it up.
__________________
maxwedge is offline   Reply With Quote
Old 05-01-2023, 07:11 PM   #5
ducked
AF Newbie
Thread starter
 
Join Date: Sep 2022
Location: Tainan
Posts: 55
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Thanks. Might take a bit more than a light hone though.

Now thinking this might be corrosion damage, with the corrosion pits cleaned out by later engine operation (though if so it seems to have been surprisingly thorough)

There is some rust evident around the edges of the bright metal pitting.

https://photos.google.com/album/AF1Q...ImfxnFGy2hU5wT

It'd be nice to know what caused it, since otherwise it might continue happening
ducked is offline   Reply With Quote
Old 05-01-2023, 08:05 PM   #6
RidingOnRailz
AF Enthusiast
 
RidingOnRailz's Avatar
 
Join Date: Jun 2009
Location: Stamford, Connecticut
Posts: 753
Thanks: 44
Thanked 15 Times in 15 Posts
Cool Re: Cylinder Wall Pre-Ignition Damage?

Quote:
Originally Posted by maxwedge View Post
Yes a lite hone to clean it up.
Link to photo in post #5 = 404 .....
RidingOnRailz is online now   Reply With Quote
Old 05-01-2023, 11:59 PM   #7
ducked
AF Newbie
Thread starter
 
Join Date: Sep 2022
Location: Tainan
Posts: 55
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Quote:
Originally Posted by RidingOnRailz View Post
Link to photo in post #5 = 404 .....
Yes, SORRY. was working , now it isn't

ALTERNATIVE

https://forumosauploads-12829.kxcdn....2_666x500.jpeg
ducked is offline   Reply With Quote
Old 05-02-2023, 08:58 AM   #8
maxwedge
A990 racer
 
Join Date: Mar 2002
Location: Chestertown, New York
Posts: 16,942
Thanks: 25
Thanked 369 Times in 363 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Yeh, better view, make sure there is no crack behind that area.
__________________
maxwedge is offline   Reply With Quote
Old 05-03-2023, 02:13 AM   #9
ducked
AF Newbie
Thread starter
 
Join Date: Sep 2022
Location: Tainan
Posts: 55
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Quote:
Originally Posted by maxwedge View Post
Yeh, better view, make sure there is no crack behind that area.
Not sure how I would do that. I can't see any sign of a crack, but I can try and get a higher resolution picture than this (iPhone) one.

I suppose dye penetration testing would be one approach, but I dunno if I can get an appropriate dye test kit in Taiwan.

Maybe dyed penetrating oil, or just nail varnish diluted a bit further with acetone?

GF probably wouldn't miss a little bit.
ducked is offline   Reply With Quote
Old 05-23-2023, 06:10 AM   #10
ducked
AF Newbie
Thread starter
 
Join Date: Sep 2022
Location: Tainan
Posts: 55
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Now thinking this might be spalling damage from cavitation in the water jacket, like what you get on the inside of tank armor from a non-penetrating round impact or explosion.

images.app.goo.gl/2MyRtRdW2BwW7prp6

Plenty of discussion of cylinder liner cavitation (mostly in the context of heavy duty diesels) out there, for example

http://www.constructionequipment.com...maintenanc...s

but I have not seen any mention of corresponding spalling inside the cylinder, so thatís just my speculation.

If that IS the cause, there will be corresponding pits inside the liner, and it might have been promoted by my practice of boiling the coolant to clear air pockets. Might have to figure out a vacuum fill method instead, a hassle I could do without.

Probably worth trying a different coolant (I used Shell last fill) and maybe changing the rad cap.

Canít think of anything else.

There doesn't seem to be any mention of a procedure for changing the cylinder linere in the manuals I have, so maybe its considered a specialist machine shop job.
ducked is offline   Reply With Quote
Old 06-15-2023, 10:36 PM   #11
ducked
AF Newbie
Thread starter
 
Join Date: Sep 2022
Location: Tainan
Posts: 55
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Cylinder Wall Pre-Ignition Damage?

Or could it be spalling due to thermal shock, from water droplets hitting the cylinder wall?

IIve done water decokes a few times, using a plant sprayer, and for a while I rigged an IV line to suck water in at relatively high revs using the negative pressure generated inside the air cleaner. It seems rather more linear than I would expect, but I dont really know.

This cylinder seemed to have less carbon than the others, consistent with it having got more water

In future (if there is one) ill maybe restrict water decokes to using steam rather than liquid water.
ducked is offline   Reply With Quote
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Engineering/Technical

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 01:52 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts