1995-2003 S10 & Blazer Front End Clunk Pop Fix!!! Read!! - Page 7

BlazerLT · #91 02-28-2005, 02:23 PM

Very true, good point.

91s10blazer · #92 03-28-2005, 12:01 AM

Will this clunk fix work on the 1st gen. Blazers as well? I have a '91 and the sound of it is almost identical to what you guys are saying but it sounds like all your Blazers are 2nd generation.

BlazerLT · #93 03-28-2005, 12:16 AM

It will be that, or the torsion bar mounts for the first gen.

Big_ Easy · #94 05-31-2005, 02:43 PM

Quote:

Originally Posted by Alexxn 00 Si

Just got mine...I'll let everyone know when they are installed....

I just got back from the dealer and they do not have the part listed. Do you have the number which you could pass on, much appreciated.

blazee · #95 05-31-2005, 03:01 PM

12383460 Washer - Hood Hinge

Big_ Easy · #96 05-31-2005, 03:59 PM

Quote:

Originally Posted by blazee

12383460 Washer - Hood Hinge

Thanks for the quick response much appreciated.

DjEarth · #97 06-01-2005, 03:33 AM

Always wondered what that was. New project for tomorrow I see.

Ordered the washers this morning. $3.00 at my dealership and he wanted to know exactly why I wanted them. Then said..oh that may fix it..but most likely not.

Raijek · #98 06-03-2005, 11:25 PM

Quote:

Originally Posted by xokayxo

Part number would be the same anywhere though, right? I'm in Alaska. Didn't have time to go to the dealer today so I'll go by tomorrow. Also, I downloaded divX and watched that video, took off the black trim/cover where the hinge is on my Jimmy, wedged in a shop towel, and test drove it. No sound whatsoever. So I drove home and took out the towel, replaced the trim/cover, and I've been driving it unfixed since. AND I'M NOT HEARING IT ANYMORE!! I did the washboard thing again and there was nothing. I thought maybe since it's so cold the metal might have contracted so it's tighter now. Is it still a good idea to replace the washer so it doesn't come back or get worse later, or should I save my time?

No dude! Metal doesn't expand and contract that much

But who knows why it stopped. Good tho'

freddie cosme · #99 06-08-2005, 12:41 PM

Quote:

Originally Posted by Alexxn 00 Si

Just got mine...I'll let everyone know when they are installed....

Are these special washers that need to be purchased at the dealer are they nylon or steel

BlazerLT · #**100** 06-17-2005, 09:30 PM

Yes, they are metal.

Lt_Dusty · #**101** 06-20-2005, 10:34 AM

Hello to all. I'm new to this site, and have been searching for a cure for the clunk I've felt in the passenger floorboard (on take off, and generally right hand turns), on our 96 Blazer 4x4, for nearly a year. Ball joints, sway bar bushings, idler arm, messing around with the torsion bar mounts, and even the 7 dollar spring washers, with no fix. Although they were in need of replacing anyways. I read a suggestion (i thought was from this thread, but I cant find the post), about re-torqueing the upper A arm bolts. I had been told by numerous suspension experts, the A-arm bushings were fine. Well it seems over time the rubber from the bushings tends to shrink, allowing the a-arm to move back and forth just enough to make a clunk. I loosened the a-arm bolts allowing a little seperation, and hosed it down with white lithium grease, then re-torqued to specs. It not only cured that clunk, but another that I would sometimes get hitting pot holes, or going over rough pavement. Anyways, i thought I would post this for the people that haven't found their cause. Maybe it will save someone a couple hundred bucks.

Dusty

metallica21156 · #**102** 06-21-2005, 07:19 PM

i still have a clunck in my 95 that nobodys been able to fix. lower and upper ball joints ,anti-sway link kit and bushings have been replaced,shocks replaced, entire front ends has been gone over and its still there. hood fixed as well and its still there. took it to a friend of mine and him and his mechanic could find anything rubbing or anything that looked like it was hitting. i looked at it my self and couldn't find anything. i've also played with the torision bar cross member and its not from there either. any ideas?

ace3 · #**103** 07-27-2005, 08:59 PM

Im so glad I found this thread, Ive been chasing this clunk for weeks now .Ive spent 800 on front end parts. I hope this solves my problem....

BlazerLT · #**104** 07-27-2005, 09:14 PM

Quote:

Originally Posted by ace3

Im so glad I found this thread, Ive been chasing this clunk for weeks now .Ive spent 800 on front end parts. I hope this solves my problem....

Yea, this is what happened to me too.

Cailen · #**105** 07-28-2005, 12:44 PM

I vote this gets stickied

POST REPLY TO THIS THREAD