Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Saturn > SC/SL/SW
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 10-06-2004, 12:04 PM   #1
wilson05
AF Newbie
 
wilson05's Avatar
 
Join Date: Oct 2004
Location: coeburn, Virginia
Posts: 97
Thanks: 0
Thanked 0 Times in 0 Posts
Send a message via ICQ to wilson05
Angry throw out bearing problems!!!

If there is anyone with an answer to the following question either leave me a reply on here or get on icq and add me 104056640. Any ways
I have a 99 Saturn SC1 and theres a problem. The slave cylinder popped out of place where the throw out bearing hits the pressure plate.
when this happened i tried to put the slave cylinder back in place and the throw out bearing fell down inside the motor i guess .... How can i get this fixed?
wilson05 is offline   Reply With Quote
Old 10-07-2004, 12:09 AM   #2
sierrap615
Master Tech Wanna-be
 
Join Date: Jul 2003
Location: Downers Grove, Illinois
Posts: 2,728
Thanks: 0
Thanked 0 Times in 0 Posts
Re: throw out bearing problems!!!

the throw out bearing rest on the transmission input shaft, unless it cracks into two it can't fall inside the bellhousing.

i highly doubt this problem is as bad as it sound. i myself would seperate the transmission and engine and look inside the bellhousing only if i knew for a fact something was in there(as there is no inspection plate)

ask the techs on saturnfans.com

this picture may help - http://www.saturnfans.com/photos/sho...php/photo/6935

heres how-to R&R the clutch -
http://www.saturnfans.com/forums/sho...threadid=23753
sierrap615 is offline   Reply With Quote
Old 10-11-2004, 11:56 AM   #3
wilson05
AF Newbie
Thread starter
 
wilson05's Avatar
 
Join Date: Oct 2004
Location: coeburn, Virginia
Posts: 97
Thanks: 0
Thanked 0 Times in 0 Posts
Send a message via ICQ to wilson05
Re: throw out bearing problems!!!

Well thanks, I knew it would be more simple than i thought to fix but theres one more questions.... How hard is it to get the tranny off? and How do i do it?
wilson05 is offline   Reply With Quote
Old 10-11-2004, 10:33 PM   #4
sierrap615
Master Tech Wanna-be
 
Join Date: Jul 2003
Location: Downers Grove, Illinois
Posts: 2,728
Thanks: 0
Thanked 0 Times in 0 Posts
Re: throw out bearing problems!!!

you don't need to pull the whole transmission, the R&R procedure above should give you enough room to see what you need to see. but if you do really want to pull the whole thing out - http://www.saturnfans.com/forums/sho...threadid=29795
sierrap615 is offline   Reply With Quote
Old 10-13-2004, 12:29 PM   #5
wilson05
AF Newbie
Thread starter
 
wilson05's Avatar
 
Join Date: Oct 2004
Location: coeburn, Virginia
Posts: 97
Thanks: 0
Thanked 0 Times in 0 Posts
Send a message via ICQ to wilson05
Exclamation re throw out bearing?

Ok mabye i act like i know what i'm talking about but I dont believe i do but anyways the throwout bearing i was talking about that fell into the motor .... i believe what i was talking about that fell in wasnt the throwout bearing... it was a pin that when the clutch was pushed the pin pushed on something in the bell housing.... that pin is what fell inside ... should i try and fix it the same way?
wilson05 is offline   Reply With Quote
Old 10-14-2004, 12:16 AM   #6
sierrap615
Master Tech Wanna-be
 
Join Date: Jul 2003
Location: Downers Grove, Illinois
Posts: 2,728
Thanks: 0
Thanked 0 Times in 0 Posts
Re: throw out bearing problems!!!

don't worry, i know what you mean. seperate the trans and engine according to the clutch R&R and a bet that pin will drop right out, i'm just sorry there isn't a easier way to do it.
sierrap615 is offline   Reply With Quote
Old 10-18-2004, 01:36 AM   #7
sierrap615
Master Tech Wanna-be
 
Join Date: Jul 2003
Location: Downers Grove, Illinois
Posts: 2,728
Thanks: 0
Thanked 0 Times in 0 Posts
Re: throw out bearing problems!!!

WOO-HOO, never so gain i'm wrong. there is an inspecton plate. normally its on the bellhousing facing the trans. but for the 1.9 liter, it is attached to the bellhousing underneth the engine. let me see if i can find a photo...
sierrap615 is offline   Reply With Quote
Old 10-18-2004, 02:08 AM   #8
sierrap615
Master Tech Wanna-be
 
Join Date: Jul 2003
Location: Downers Grove, Illinois
Posts: 2,728
Thanks: 0
Thanked 0 Times in 0 Posts
Re: throw out bearing problems!!!

ok, this is all i could find. its on the right, haft-way covered by the timing chain cover.

http://www.saturnfans.com/photos/sho...p/photo/15134/
sierrap615 is offline   Reply With Quote
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Saturn > SC/SL/SW

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 12:12 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts