Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Pontiac > Grand AM
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 04-26-2010, 02:26 AM   #1
BrandonMurray
AF Newbie
 
Join Date: Apr 2010
Location: Niagara Falls
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
cooling system back pressure, heater not working

heyy, I have a 99 grand am GT and for some reason when you leave it running long enough it will shoot all of my anti-freeze out of the over flow. I've done a full flush, changed the thermostat, and taken the rad out to clean it. Even though i've done all this there still seems to be back pressure.

Also my heater doesnt work while all this is going on. When i clamped the #2 hose off in the picture below, all of the problems seem to go away and coolant starts to flow through the heating tubes again.



any suggestions would be greatly appreciated, i'd rather not have to drive around with vice grips on that hose hahah
BrandonMurray is offline   Reply With Quote
Old 04-26-2010, 06:44 AM   #2
3100
Banned
 
Join Date: Nov 2008
Location: chicago, Illinois
Posts: 1,034
Thanks: 0
Thanked 2 Times in 2 Posts
Re: cooling system back pressure, heater not working

make sure you have enough coolant and bleed air from the screw by your number 1 on the picture.
3100 is offline   Reply With Quote
Old 04-26-2010, 10:17 AM   #3
skeeter123
AF Regular
 
Join Date: Jul 2009
Location: melbourne, Florida
Posts: 181
Thanks: 0
Thanked 2 Times in 2 Posts
Re: cooling system back pressure, heater not working

Make sure that your cooling system is coming up to operating pressure. When cold, squeeze radiator hose to see how it feels with no pressure. Start it up and let it run 15-20 minutes, till coolant temp is ~195deg. (stock thermostat temp). Squeeze the radiator hose, should be under pressure. No pressure = leak somewhere, and your coolant will boil out (coolant boils at lower temp when not under pressure). Usually it's the coolant reservior cap that leaks, its supposed to hold up to 15psi. You can get a replacement ~$5 at parts store. Sometimes it's the reservoir itself that won't hold the pressure.
Hope this helps.
skeeter123 is offline   Reply With Quote
Old 04-26-2010, 09:51 PM   #4
BrandonMurray
AF Newbie
Thread starter
 
Join Date: Apr 2010
Location: Niagara Falls
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Re: cooling system back pressure, heater not working

thats very helpful thank you, i think i'm going to buy a new resevoir tank because there is a small leak in the side. could it be the intake gaskets? i've heard a lot of stories about that being the problem with grand am's
BrandonMurray is offline   Reply With Quote
Old 04-27-2010, 09:25 AM   #5
skeeter123
AF Regular
 
Join Date: Jul 2009
Location: melbourne, Florida
Posts: 181
Thanks: 0
Thanked 2 Times in 2 Posts
Re: cooling system back pressure, heater not working

I have a little pet theory (no proof) that it's the other way around: that on a lot of these 3.4L v6's there's a coolant-pressure leak (either the cap, reservoir, hose, water pump, etc.... all common) that when it happens causes the system to loose presssure, loose coolant, get too hot in bad places, and result in/cause the LIM gasket problem to happen, when it might have been postponed or never happen if the system hadn't leaked. The LIM gaskets are always just waiting to go (re the critical concern about under/over-torqueing the bolts), and the multiple weak points in the cooling system are the triggers.
Speaking of weak points, are you using Dexcool for coolant? I flushed mine out real good and switched to prestone green stuff. Dexcool will get sludgy if a little air is left in after changing the fluid. It will also create sludge if it's mixed with green coolant, so if you switch you have to flush it out pretty good. Sludge can block passageways, cause hot spots, lead to LIM gasket failure. See http://www.automotiveforums.com/vbul...d.php?t=718130
for coolant-bleed procedure.
And i hate to mention it but: when you put the new reservoir on, immediately on start up check to see if the radiator hoses are under a lot of pressure. Lots of pressure before engine has time to warm up indicates a head gasket leak, which could certainly pop the reservoir in half.
skeeter123 is offline   Reply With Quote
 
Reply

POST REPLY TO THIS THREAD


Tags
back , cooling , heating , pressure , system
Go Back   Automotive Forums .com Car Chat > Pontiac > Grand AM

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:34 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts