Picture Detailing all 11 Grease Zerk Locations

swalt · #1 01-08-2005, 11:48 PM

I have seen this question come up a few times. I won't take credit for it as I found the pic on an S10 forum, but figured it would be a great help for those who want to know where all the zerks are. By the way, this highlights all 11 fittings, but if you have had your U joints replaced, you have two more to grease at the front and rear of the drive shaft.

BlazerLT · #2 01-09-2005, 08:06 PM

Excellent!

texwill · #3 01-10-2005, 03:48 AM

Great info, will be doing that today!

BlazerLT · #4 01-10-2005, 12:07 PM

Yea, would be a good idea.

And also grease your u-joints if they are aftermarket and have been replaced in the past.

97blazermadness · #5 01-10-2005, 01:22 PM

That pic has helped me tremendously!

Phillip Cross · #6 01-10-2005, 05:03 PM

My 2000 is missing a lot of those Are they to be installed by owner for better maintenance???

blazee · #7 01-10-2005, 05:13 PM

If your's has grease plugs, you will have to buy grease fittings, just remove the plug and screw the fitting in it's place.

If you have a 4wd your lower ball joints are different, the fittings will be on top of the ball joint.

If you have skid plates, they are blocking your view of the idler arm and pitman arm fittings.

BlazerLT · #8 01-10-2005, 05:17 PM

Sealed balljoints cannot be greased, only aftermarket.

Phillip Cross · #9 01-10-2005, 05:22 PM

Is it worth installing fittings/ I have 75K on my 2000 4wd

blazee · #10 01-10-2005, 05:25 PM

Yes, it is worth it, if you want to prevent premature wear of your front end. You should grease them at least every 7,500 miles or 6 months. I do mine every 6,000 when I change the oil.

BlazerLT · #11 01-10-2005, 05:32 PM

As stated earlier, sealed balljoints usually can't have a zerc installed but by what I have seen, most should have the grease fitting installed from the factory.

Mine did. If not, they are sealed and can only be replaced, not greased.

blazee · #12 01-10-2005, 05:39 PM

Mine had them when I got it too, but the Haynes book says occassionally they come with plugs and can be changed out to fittings. I haven't seen any like this myself, but appearently they are out there.

And yes sealed ones can not be greased.

BlazerLT · #13 01-10-2005, 05:49 PM

Quote:

Originally Posted by blazee

Mine had them when I got it too, but the Haynes book says occassionally they come with plugs and can be changed out to fittings. I haven't seen any like this myself, but appearently they are out there.

And yes sealed ones can not be greased.

From what I have seen, they are greased and sealed.

Only way to maintain them is to replace them with after market with grease fittings.

Bobobuoy · #14 09-10-2019, 11:55 PM

Hi, Newish member here. Why am I getting this Error message when trying to click the link to the .jpg file:

Forbidden

You don't have permission to access /gallery/watermark.php on this server.

I was able to open a different picture link, but can't get this to open, and really want to see the info. Would like some help with this.. Thanks

Bobobuoy · #15 09-11-2019, 12:04 AM

OK, sorry for my new-ness, but I found out 2 things since my last post about not being able to open the link to the picture:
1/ I was seeing the page in "print view" mode, not in normal forum reading mode, so that might have affected the picture's link

2/ When I did get into normal forum reading mode, I don't see the link AT ALL.. So obviously I still can't open it, to see the info.. What's up with this?

Thanks again../Bob

POST REPLY TO THIS THREAD