|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| Let's get Technical! Discussion for hardcore in-depth motor heads! |
 |
 Show Printable Version | 
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
03-30-2008, 11:59 PM
|
||||
|
||||
|
Resurface head
What do you guys think is a reasonable, average, and highest and lowest price to pay to have a GSR head resurfaced at a machine shop? Thanks in advance.
__________________
JDM B18C, LSD tranny, Exedy flywheel/clutch, AEM intake, Greddy cat back, stainless header, Skunk2 manifold, Koyo radiator, Tokico Illumina full coilovers, black 17" Konig Hurry's, dc strut bars, custom cf hood, poly motor mounts, alum. battery bracket, b&m short shifter, Viper alarm, spoon chip, Tenzo R seats, Kenwood amp, Pioneer and MTX speakers w/cross over's, euro antenna, NGK wire's and plugs, Mobil 1 syn. and a whole lot of attitude. 9.4 sec 1/8 mile at Irwindale 4/20/06 
|
|
#2
03-31-2008, 02:05 PM
|
||||
|
||||
|
Re: Resurface head
All depends on what you want done, anything extra?
|
|
#3
03-31-2008, 02:44 PM
|
||||
|
||||
|
Re: Resurface head
Nothing extra. I just want it resurfaced flat so that I can install a new head gasket. I'm confident that I don't need a valve job and I plan on polishing out the ports myself. If I did have them do anything else it would be to get that damn compression gauge hose out of the spark plug threads.
__________________
JDM B18C, LSD tranny, Exedy flywheel/clutch, AEM intake, Greddy cat back, stainless header, Skunk2 manifold, Koyo radiator, Tokico Illumina full coilovers, black 17" Konig Hurry's, dc strut bars, custom cf hood, poly motor mounts, alum. battery bracket, b&m short shifter, Viper alarm, spoon chip, Tenzo R seats, Kenwood amp, Pioneer and MTX speakers w/cross over's, euro antenna, NGK wire's and plugs, Mobil 1 syn. and a whole lot of attitude. 9.4 sec 1/8 mile at Irwindale 4/20/06
|
|
#4
03-31-2008, 03:00 PM
|
||||
|
||||
|
Re: Resurface head
i would first measure to see if you need a resurfaced head... if its still within spec, it may be a waste of money
|
|
#5
03-31-2008, 07:47 PM
|
||||
|
||||
|
Re: Resurface head
Well I called around today and found a shop that will resurface it for only $30. So how do you determine if the head is within spec? What tools or equipment would I need?
__________________
JDM B18C, LSD tranny, Exedy flywheel/clutch, AEM intake, Greddy cat back, stainless header, Skunk2 manifold, Koyo radiator, Tokico Illumina full coilovers, black 17" Konig Hurry's, dc strut bars, custom cf hood, poly motor mounts, alum. battery bracket, b&m short shifter, Viper alarm, spoon chip, Tenzo R seats, Kenwood amp, Pioneer and MTX speakers w/cross over's, euro antenna, NGK wire's and plugs, Mobil 1 syn. and a whole lot of attitude. 9.4 sec 1/8 mile at Irwindale 4/20/06
|
|
#6
03-31-2008, 08:17 PM
|
||||
|
||||
|
Re: Resurface head
30$??? that doesnt sound right.... and you can get a FSM and look at the procedure there
|
|
#7
03-31-2008, 09:27 PM
|
||||
|
||||
|
Re: Resurface head
Quote:
I know this might sound funny but what exactly is an FSM?
__________________
JDM B18C, LSD tranny, Exedy flywheel/clutch, AEM intake, Greddy cat back, stainless header, Skunk2 manifold, Koyo radiator, Tokico Illumina full coilovers, black 17" Konig Hurry's, dc strut bars, custom cf hood, poly motor mounts, alum. battery bracket, b&m short shifter, Viper alarm, spoon chip, Tenzo R seats, Kenwood amp, Pioneer and MTX speakers w/cross over's, euro antenna, NGK wire's and plugs, Mobil 1 syn. and a whole lot of attitude. 9.4 sec 1/8 mile at Irwindale 4/20/06
|
|
#8
03-31-2008, 10:05 PM
|
||||
|
||||
|
Re: Resurface head
FSM = Factory Service Manual
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
