|
| Search | Car Forums | Gallery | Articles | Helper | Air Dried Beef Dog Food | IgorSushko.com | Corporate |
|
|||||||
| Interior | Audio | Security Tech forum to assist in Honda/Acura Interior, Audio and Security. |
 |
 Show Printable Version | 
Subscribe to this Thread
|
|
|
Thread Tools |
|
#1
08-05-2005, 05:29 AM
|
|||
|
|||
|
kill switch
I just got my civic stolen and now I have another one I have a 91 si hatch I want to install a hidden kill switch on the ingnition line so that no ass hole can have my car. Has anyone done this to there car or have any idea of how to I already have the switch and spot I am going to put it but wanted to know what you all thought.
word 
|
|
#2
08-28-2005, 05:16 PM
|
||||
|
||||
|
Re: kill switch
i'm about to do the same. you'll need some 12gauge wire, some Male and Female connectors, and a hiding place. cut into the power wire for the ignition and wire in your switch. it should work. try NOT to put the switch under the hood, dash, or in the glove box. because those are too obvious.
|
|
#3
08-28-2005, 06:39 PM
|
||||
|
||||
|
I have done this in my integra, but instead of the ignition I have two switches (might be a little overkill) that kill the fuel pump. It has worked very well; there have been two unsuccessful attempts by thieves to steal the car since I installed the switches. I do, however, have a clutch lock so the switches cannot be given all the credit, but they make me sleep better at night.
|
|
#5
08-30-2005, 04:02 AM
|
||||
|
||||
|
Re: kill switch
check these out, they majorly helped me out. i'm starting tomorrow.
how-tos: http://members.cox.net/shaundrake/al...AlarmMods.html http://www.jdmuniverse.com/forums/sh...threadid=20052 wiring: http://www.bulldogsecurity.com/diagrams/diagrams.htm
|
|
#6
09-01-2005, 03:23 AM
|
||||
|
||||
|
Re: Re: kill switch
I find it easiest to use the NEGATIVE coil wire. All you do is loop through a single pole METAL switch. It's basically like a light switch. Run the negative coil wire to the switch and a wire from the switch back to the coil. Simple, 5 min your done.
|
|
#7
09-01-2005, 12:51 PM
|
||||
|
||||
|
Re: kill switch
do you have a pic? here's mine...
 ... i hooked it up to the 10ga black/yellow wire coming out of the starter. Last edited by crazi-85crx; 09-01-2005 at 04:07 PM.
|
|
#8
09-03-2005, 10:28 PM
|
|||
|
|||
|
Re: kill switch
This Article, in bold and hilighted at the beginning of this subsection, has a very nice guide. I'm surprised you didn't find it before.
__________________
BD (Before Deer): Clean... Very Clean. AD (After Deer): Nascar Ready.   Go Baby Go.
|
|
#9
09-04-2005, 11:01 PM
|
|||
|
|||
|
Re: Re: kill switch
Quote:
__________________
99 [email protected] psi si- I voted for the Terminator for Gov. 95 HB- B16a2- SC34@12psi WTB: USDM B16a2 or B16a3 complete short block. pm is the key. FS: B series InlinePro cast mani, PnH RC 550s, and Hondata S2b. pm me.
|
|
#10
09-05-2005, 01:49 AM
|
||||
|
||||
|
Re: Re: Re: kill switch
Quote:
__________________
|
|
|
POST REPLY TO THIS THREAD |
 |
|
|
