Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys

Stop Feeding Overpriced Junk to Your Dogs!

GET HEALTHY AFFORDABLE DOG FOOD
DEVELOPED BY THE AUTOMOTIVEFORUMS.COM FOUNDER & THE TOP AMERICAN BULLDOG BREEDER IN THE WORLD THROUGH DECADES OF EXPERIENCE. WE KNOW DOGS.
CONSUMED BY HUNDREDS OF GRAND FUTURE AMERICAN BULLDOGS FOR YEARS.
NOW AVAILABLE TO THE GENERAL PUBLIC FOR THE FIRST TIME
PROPER NUTRITION FOR ALL BREEDS & AGES
TRY GRAND FUTURE AIR DRIED BEEF DOG FOOD
Go Back   Automotive Forums .com Car Chat > Chevrolet > Cobalt
Register FAQ Community Arcade Calendar
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 07-09-2009, 12:52 PM   #1
rodeo02
AF Enthusiast
 
Join Date: Mar 2003
Location: Buffalo, New York
Posts: 3,213
Thanks: 0
Thanked 4 Times in 4 Posts
2007 Cobalt, new lower control arm bushings..

My 2007 Cobalt at 31500mi out of the blue started making this horrible front-end clunk over bumps at lower speeds. I suspected maybe stabilizer bar end links having been down that road before with Chevys and Fords?? Nope, they feel tight as new? Jacked it up, got underneath as best I could, couldn't find any play or noises anywhere. Of course this was after accidentally grabbing the catalytic converter and burning the finger prints off several fingers. (scorching hot after 20sec BTW thanks to GM's air injection :!) Anyhoo.. frustrated I called the dealer I bought it from. They set me up with an appointment the next day. Long story short? Per the invoice; The front lower control arm bushings had to be replaced on both sides, plus a front end alignment. All on GMs dime. Even got shuttle rides. No fuss, no muss. Is it common for these things to go from all to nothing in one swoop? The car has always been tight and clunk free?

Joel
__________________
2016 Subaru Forester 2.5i base CVT
2016 Nissan Quest SV
rodeo02 is offline   Reply With Quote
Old 07-06-2010, 05:47 PM   #2
sassygramma
AF Newbie
 
Join Date: Apr 2006
Location: weston
Posts: 11
Thanks: 0
Thanked 0 Times in 0 Posts
Re: 2007 Cobalt, new lower control arm bushings..

Getting here bit late on your post but wanted to let you know that I have a 2007 Cobalt LT Sedan, 2.2 - 4 cylinder, bought new Jan. 22, 2007 . Had 15 miles on it (8 of which we put on during test drive) when we pulled off lot. Has been a fairly decent car up until the recall on the power steering motor.

When I took it in for that replacement, I had mentioned that recently there was a small clunk from front end, going over even the smallest of bumps, which seems to be progressing to a bigger clunk in last few weeks, sounds like whole front end going to fall off and asked if they could confirm if the lower front control arms were going bad. (Thanks to forums like this, I didnt look like a total fool and actually acted like I knew what I was talking about ). It took approximately 10 seconds for a guy on the ground looking at each side for them to say, YES they are almost on the ground, and need to be replaced.

Well, I am out of my warranty by 5 months, and the kicker is I only have 13725 miles on car !! So to answer your question, yes these parts can fail at moments notice. I am so upset right now that with mileage like I have, I am already faced with putting money into this car. What can I expect in the next 13k miles to have to replace? I have learned my lesson, and will now make sure to let anyone who wants to listen to not buy a GM vehicle. Our old '01 Impala (bought with 7500 miles on it in 2001) was nothing but a headache, and now same with this vehicle.
sassygramma is offline   Reply With Quote
 
Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Chevrolet > Cobalt


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 11:42 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts