Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat

HeWhoKillz HeWhoKillz is offline

AF Regular

Visitor Messages

Showing Visitor Messages 1 to 6 of 6
  1. Silverwingsto
    07-15-2016 06:55 PM
    Silverwingsto
    Please help me to know how to make a post on here? Thanks
  2. curtis73
    11-26-2009 09:33 AM
    curtis73
    The axles will spline up easy. Its just the last 1" that is the tough part. That's when you're trying to seat that snap ring. The first 3" or so that you slide it in, that's the splines meshing. The tough part is the snap ring groove at the end.
  3. HeWhoKillz
    11-25-2009 12:54 PM
    HeWhoKillz
    Doesn't pounding it in like you say damage the splines that are trying to mesh with the splines on the transmission input? However I have been just pushing and waiting. I didn't know how fragile the axles might be so I didn't want to just ram it in. I'm going to have to try this ramming procedure. I haven't tried that yet. I just get it in as far as I can go and attempt to push in from that spot which doesn't work.
  4. curtis73
    11-24-2009 08:07 PM
    curtis73
    The clip is supposed to look warped. its not perfectly round. Grab the outer end of the axle and push in on it. The CV joints slide in and out to allow for length changes during suspension articulation and steering. Now, slide the axle into the transmission and do the same thing but do it like you're angry. Pound it in using that compression. Don't just push and wait, pound it. Slam those puppies home. If you're not afraid of knocking the car off the jackstands, you're not doing it hard enough

    Don't take the boot off... there is no reason for it, and its a mess. Its full of a thin grease that is the consistency of sour cream.
  5. curtis73
    11-22-2009 11:48 PM
    curtis73
    You can't remove it. The CV joints have enough compression space that they can float in and out without that clip. At the very least it will cause massive leaking at the axle seals. At the worst, the axle will come out of the transmission and cause major damage.

    The axle should slide in easily to a point. Some let the ring snap in easily, others are a pain. The best way to do it is to apply your pressure or impacts with the axle straight - not angled. If the axle is angled up, then you're forcing the ring against the bottom of the hole.

    Two ways that always seem to work for me. On easy axles, I grab the splined hub end of the axle and ram it in compressing the CV joints until they hammer the axle into place. If that doesn't work I use a long extension and a hammer. Put the extension on the inner CV joint and give it a good whack. Sometimes it also helps if you try pushing it in by the inner joint. A straight insertion often works easily.
  6. curtis73
    11-19-2009 10:58 PM
    curtis73
    The point of the axle clips is to prevent the axle from "walking" out. As the suspension travels up and down, the length of the axle changes. The point of the clip is to hold the inner joint in place during that travel. Theoretically, if it weren't there, the inner axle could get pulled out during extreme articulation. The clip gently holds the inner joint in place so it can't move.

About Me

  • About HeWhoKillz
    City
    columbus
    State
    Indiana
    Zip Code
    00000
    Country
    United States

Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: 10-03-2023 04:09 PM
  • Join Date: 04-29-2005
  • Referrals: 0

All times are GMT -5. The time now is 07:12 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.