bumper lights stay on

does anybody know how to make the bumper lights stay on???

replace bulbs w/ double fillament ones and tap lead to corner signal lights...try replacing bulbs first before rewiring...

i dont wanna buy anything before i know that i could do it myself,, but thanks for replying??? today i briged the inner corner bulb to the bumper light. it worked but the outer light doesnt turn on and it doesnt singal... i wuz thinkin of getting the pos from the inner light and brigeing it to the neg bumper light.. i have it done yet but i will..

just to let you know...you can rewire it all you want but if the bulb is not made to light up and signal at the same time, you're wasting your time.:flash:

Note this how to is for a 5th gen accord, but should work for our civics too.

Originally posted by AccordLX @ nwhonda.net
Always On Bumper lights

Stuff you'll need :
4X male Disconects
Wire
2X 1157 bulb harness (got mine from napa, 87-89 accord brake bulb harness PN:LS6253 )
2X amber (or any color) bulbs
wire splice connectors

---------------------------------------------------------

1. remove Bumper Lamp, pull out wire
http://images.cardomain.com/installs/227000-227999/227912_2_full.jpg


2. Remove black bulb socket
http://images.cardomain.com/installs/227000-227999/227912_3_full.jpg


3. You'll need 4 male disconects
http://images.cardomain.com/installs/227000-227999/227912_4_full.jpg


4. Take a 1157 Harness and Wire/hook-up 2 of the Male disconects to the GROUND and the HighBeam wire(if you got the harness from Napa, both are black)
http://images.cardomain.com/installs/227000-227999/227912_5_full.jpg


5. Remove a Corner Lamp.
http://images.cardomain.com/installs/227000-227999/227912_7_full.jpg


6. i have black housing depos, so there is only one bulb per corner (the only one that fits doesn't blink). so what i did instead of ruining the bulb harness, was disconect the positive + from the one that is always-on (and fits the corner) and splice into the positive of the blinking/always on bulb harness. so i already had the always-on wire exposed
http://images.cardomain.com/installs/227000-227999/227912_6_full.jpg
if you don't have JDM or JDM style Corners than you can just splice into the positive of the one thats always on.


7. run you wire that you spliced into from the corner down to bumper. with the male disconects attached to the HighBeam & ground wires of the harness, they should just push into the original bumper/blinker harness. splice the wire from corners into
the third LowBeam wire of the bulb harness(if you got the harness from napa, it is red)
http://images.cardomain.com/installs/227000-227999/227912_9_full.jpg


8. My Wiring Diagram (This may be easier to understand)
http://images.cardomain.com/installs/227000-227999/227912_10_full.jpg


I am not responsible for anything you do, etc., blah, blah. i write these directions on how to do my car : 1994 Accord LX. so your car may be different

i just did it right now with no money down. i pretty much did the same thing but i..... do u guys wanna know?? cuz its going to be long..

sure, I could use a better how to. There is a CRX here in napa that did it, but he isnt sure WTF he did, and only one of his works.

ok this is what i did... . u know that the inner corner light stays on when u turn on the head lights rigth so i did this i cut the wires from the inner corner light and i cut the bumper wires off i rerouted the inner corner wires to the bumpers bulb. i did the same with the bumpers wires. i connected them and it work. the bumper light stays on when turning on the head lights. the inner coner light now stays off. when u singal both of the corner lights blink at a fast rate also.


do u guys get it???

yeah, except i dont like the hyperblink effect...