How does this 2.3 stroker look?

Was wondering what people think of this motor?
Stage 3 2.3 Stroker....
All Built already

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=7988709911&ssPageName=MERC_VI_RSCC_Pr4_PcY_BIN_Stores_IT

Check out the bottom of the page also, they have a 850hp stage 3 6 bolt motor....mad nice but really REALLY expensive (but I can always dream...)

Thanks for the advice...

Read in there... it says its an Evo 8 engine so it wont work for our cars. Way too much IMO, you could build one for a lot less than that. It did look good though, the parts n' shit they used.

Read in there... it says its an Evo 8 engine so it wont work for our cars. Way too much IMO, you could build one for a lot less than that. It did look good though, the parts n' shit they used.

Just a question...why does it say DSM in a few places on the page?

Just a question...why does it say DSM in a few places on the page?

Ebay advertising. They use any words they can to sucker people in and get more hits on their page so more people have a chance to buy it. It worked on you didn't it? Haha.

Ebay advertising. They use any words they can to sucker people in and get more hits on their page so more people have a chance to buy it. It worked on you didn't it? Haha.


LOL.....indeed it did

Under "see more items from this seller" there are a bunch of DSM options. They do seem expensive though, and I have no experience with Jackson Auto Machine with DSMs. They are a pretty big Honda vendor as far as I know though. I think I would stick to the standard DSM vendors, like SBR, buschur, etc.

I've been hearing alot about this JAM lately and they seem to be a pretty good company (even though they work on Honduhs and all), but they seem to be very expensive. I'd say if you wanted to spend all that money it probably wouldn't hurt to go with that setup, but you could find the same setup for quite a bit cheaper at other places.

You could try ffwdconnection.com thats where i orderded my stroker kit from. They only do 4g63's and they are pretty cheap. They use good parts too, darren is really knowledgeable and will answer any questions you have.

You could try ffwdconnection.com thats where i orderded my stroker kit from. They only do 4g63's and they are pretty cheap. They use good parts too, darren is really knowledgeable and will answer any questions you have.

How much are they paying you to advertise for them? :p

well, they did send his shit out pretty fast, I might be getting cams from them when I need to do the timing belt job

How much are they paying you to advertise for them? :p
I was going to ask the same question.

I say SBR FTW. Even the stage 3 short block from them is only like $3700. Or you could just rip yours apart. IIRC, you should be able to build yourself a stroker bottom end for like $2000-$2500.

The stage 3 kit from sbr is $1500. Thats the route I'm going to go.

I was talking about the short block itself, not just the stroker kit. I do gotta say though, that stage 3 kit looks pretty sweet. I like how you can pick your compression ratio.

If I have to rebuild the bottom end on my car, its staying 2.0. Yeah, bigger turbos will like the extra displacement, but I wont get that big into turbos.

I want to go with a stroker for the added low end torque

How much are they paying you to advertise for them? :p
LOL, i did kind of sond like a salesman didn't I? I jst really liked the place decent prices and the owner (darren) was really cool. BTW I'm getting my shit tomorrow!!!

How long until that bitch is tearing up the road?

Well I'm hoping less than 2 weeks depending on how long the machine shop takes.