keyless entry
PSmith1227
03-25-2006, 02:47 PM
Can anyone please help me program my remote to unlock , lock and open the sliding door . The Number is GM 10245951. I have tried all I can think of.:banghead:
GregA
03-25-2006, 04:47 PM
Can anyone please help me program my remote to unlock , lock and open the sliding door . The Number is GM 10245951. I have tried all I can think of.:banghead:
Hello & Welcome to the forum!
I believe you will find the instructions over in the Pontiac Montana Forum.
Here is a link: http://www.automotiveforums.com/vbulletin/showthread.php?t=160122
Let us know what happens.
Take Care,
Hello & Welcome to the forum!
I believe you will find the instructions over in the Pontiac Montana Forum.
Here is a link: http://www.automotiveforums.com/vbulletin/showthread.php?t=160122
Let us know what happens.
Take Care,
Onblsht
03-25-2006, 08:34 PM
There are different remotes, but they should be interchangeable, since they all have the same 4 button circuit board, even if its a 2 or 3 button remote.
10245950 = LOCK & UNLOCK
10245951 = LOCK, UNLOCK, SLIDING DOOR
10245953 = LOCK, UNLOCK, PANIC, SLIDING DOOR
Important! Once the BCM enters program mode, all transmitters must be programmed at the same time. Any transmitters not learned at this time will be erased.
1) Remove the key from the ignition cylinder
2) Remove the BCM PRGRM fuse from the fuse panel
3) Close all the doors
4) Close the liftgate
5) Turn the ign lock cylinder to the ACC. position
6) Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second
7) Open and close front passenger door
A chime will be heard when the system enters the BCM programming mode
IMPORTANT!
After 7 seconds a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
8) Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds
9) Repeat the previous step on each additional transmitter to be programmed.
10) Remove the ignition key from the ignition cylinder
11) Install the BCM PRGRM fuse back into the fuse panel.
10245950 = LOCK & UNLOCK
10245951 = LOCK, UNLOCK, SLIDING DOOR
10245953 = LOCK, UNLOCK, PANIC, SLIDING DOOR
Important! Once the BCM enters program mode, all transmitters must be programmed at the same time. Any transmitters not learned at this time will be erased.
1) Remove the key from the ignition cylinder
2) Remove the BCM PRGRM fuse from the fuse panel
3) Close all the doors
4) Close the liftgate
5) Turn the ign lock cylinder to the ACC. position
6) Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second
7) Open and close front passenger door
A chime will be heard when the system enters the BCM programming mode
IMPORTANT!
After 7 seconds a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.
8) Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds
9) Repeat the previous step on each additional transmitter to be programmed.
10) Remove the ignition key from the ignition cylinder
11) Install the BCM PRGRM fuse back into the fuse panel.
rubberman
01-31-2007, 10:37 AM
There are different remotes, but they should be interchangeable, since they all have the same 4 button circuit board, even if its a 2 or 3 button remote.
10245950 = LOCK & UNLOCK
10245951 = LOCK, UNLOCK, SLIDING DOOR
10245953 = LOCK, UNLOCK, PANIC, SLIDING DOOR
my montana has the keyless remote of 10245952 which is lock/unlock and panic. So are you saying any of those remote part numbers will still operate the door locks? cause mine doesnt work and finding one with lock/unlock and panic is rare.
10245950 = LOCK & UNLOCK
10245951 = LOCK, UNLOCK, SLIDING DOOR
10245953 = LOCK, UNLOCK, PANIC, SLIDING DOOR
my montana has the keyless remote of 10245952 which is lock/unlock and panic. So are you saying any of those remote part numbers will still operate the door locks? cause mine doesnt work and finding one with lock/unlock and panic is rare.
Onblsht
01-31-2007, 09:47 PM
yes, they are all identical circuit boards inside. Pop yours open, you will see 4 gold colored button circuits even tho it is only 2 buttons on the case.
Automotive Network, Inc., Copyright ©2026
