engine problems
newbicivic89
12-09-2005, 06:49 PM
Ok when i crank my car up it like revs itself up then it will idle back down very low then back up then the check engine light comes on and then it will run just perfect. It will also make this poping noise then i rev it up to about 5K and it will stopp.And also my car smokes bad really bad i changed the oil in it and still have the same problem. Help would be very good.
CivicSpoon
12-09-2005, 08:50 PM
Pull the check engine light code and find out what it is.
newbicivic89
12-09-2005, 08:54 PM
Pull the check engine light code and find out what it is.
You lost me. I dont understand what your saying explain more please
You lost me. I dont understand what your saying explain more please
arodg25
12-09-2005, 09:15 PM
with the car running, look under the carpet where the passenger would put there feet and there should be a light blinking, count how many times. it will blink up to a # then pause for a sec and repeat. look here http://www.automotiveforums.com/vbulletin/showthread.php?t=118785 (the 5th post down) to find out what the code means
newbicivic89
12-09-2005, 09:40 PM
Ok thanks it blinked 3 times which means Manifold Absolute Pressure and dose that mean that tthe manifold needs to be tightend more to the head or what.
WDELOAD
12-09-2005, 10:03 PM
no u need to buy a new one..
CivicSpoon
12-09-2005, 10:13 PM
It's your MAP sensor, not the manifold.
Edit: http://www.crxpower.net/~silverkorn/manuals/CRX_Workshop_Manual.pdf Go to page 133, and get a volt meter.
Edit: http://www.crxpower.net/~silverkorn/manuals/CRX_Workshop_Manual.pdf Go to page 133, and get a volt meter.
newbicivic89
12-09-2005, 10:13 PM
No other alternatives
newbicivic89
12-09-2005, 10:18 PM
Also would that cause your car to overheat.
newbicivic89
12-10-2005, 07:52 AM
Where is the HAZARD Fuse Located at.
YZ125rider21
12-10-2005, 08:02 AM
in fuse box on passenger side wheel wall....big black box hazard fuse will be labled
newbicivic89
12-10-2005, 08:19 AM
Also if i decied to swap my stock d15b2 engine with a d16y7 non-vetch what would I have to do.
livinincalifornia
12-10-2005, 12:48 PM
convert to MPFI and rewire for it, get a new distributor with the correct sensor, get a new ECU, drop engine in.
newbicivic89
12-10-2005, 01:23 PM
convert to MPFI and rewire for it, get a new distributor with the correct sensor, get a new ECU, drop engine in.
Where could i buy a MPFI conversion kit for my car and a new distributor.
Where could i buy a MPFI conversion kit for my car and a new distributor.
civickiller
12-10-2005, 02:24 PM
does the d16y7 come with a distributor?
there are no mpfi conversion kits out there, you gotta make your own
you basically need:
mpfi intake mani complete injectors, fuel rail, tb
mpfi distributor
resistor box if going obd0
mpfi ecu
having a wiring harness for whatever obd you are goign to put in there really helps.
with on that list i put above does the y7 come with any of those things already?
there are no mpfi conversion kits out there, you gotta make your own
you basically need:
mpfi intake mani complete injectors, fuel rail, tb
mpfi distributor
resistor box if going obd0
mpfi ecu
having a wiring harness for whatever obd you are goign to put in there really helps.
with on that list i put above does the y7 come with any of those things already?
Automotive Network, Inc., Copyright ©2026