p 10 ket fob
kikey59
08-14-2005, 10:55 AM
please can you help me with resetting my remote control for the doors and alarm as it has stopped working i have tried all the advice given but i cant get in to the reprograme mode primera p10 1996 hope some one can help
J..M
08-20-2005, 08:53 PM
Standard disclaimer applies. I used the below procedure to get both of my remotes working at the same time, but if you fsck up your own remote programming, don't blame me.
J30/G20/Q45 REMOTE TRANSMITTER PROGRAMING
Model(s): 1993-94 Infiniti J30
1993.5 Infiniti G20
1994 Infiniti Q45
Classification: EL93-015
Section: Electrical
Bulletin No.: ITB93-068
Date: December 16, 1993
SERVICE INFORMATION
The proper procedure for programing additional remote controllers is listed below.
SERVICE PROCEDURE
While sitting inside the vehicle:
(1) Open the trunk.
(2) Close and lock all doors.
(3) Insert and remove the key from the ignition six times within 10 seconds.
(4) Manually unlock and lock driver's door once to enable "Belting" mode.
(5) Push lock button on the new remote controller once, just long enough to hear within 5 seconds of completing step 4.
(6) If additional remotes are needed (up to 3), repeat steps 4 and 5 for each additional remote immediately after programming the first remote.
NOTE: a total of four (4) remotes can be programmed to function on the same vehicle.
For additional information, please refer to page BF-38 of the 1993 and 1994 J30 Service Manuals: page BF-17 of the 1993 G20 Service Manual Supplement; and page EL-148 of the 1994 Q45 Service Manual.
:)
J30/G20/Q45 REMOTE TRANSMITTER PROGRAMING
Model(s): 1993-94 Infiniti J30
1993.5 Infiniti G20
1994 Infiniti Q45
Classification: EL93-015
Section: Electrical
Bulletin No.: ITB93-068
Date: December 16, 1993
SERVICE INFORMATION
The proper procedure for programing additional remote controllers is listed below.
SERVICE PROCEDURE
While sitting inside the vehicle:
(1) Open the trunk.
(2) Close and lock all doors.
(3) Insert and remove the key from the ignition six times within 10 seconds.
(4) Manually unlock and lock driver's door once to enable "Belting" mode.
(5) Push lock button on the new remote controller once, just long enough to hear within 5 seconds of completing step 4.
(6) If additional remotes are needed (up to 3), repeat steps 4 and 5 for each additional remote immediately after programming the first remote.
NOTE: a total of four (4) remotes can be programmed to function on the same vehicle.
For additional information, please refer to page BF-38 of the 1993 and 1994 J30 Service Manuals: page BF-17 of the 1993 G20 Service Manual Supplement; and page EL-148 of the 1994 Q45 Service Manual.
:)
kikey59
08-21-2005, 06:48 AM
Standard disclaimer applies. I used the below procedure to get both of my remotes working at the same time, but if you fsck up your own remote programming, don't blame me.
J30/G20/Q45 REMOTE TRANSMITTER PROGRAMING
Model(s): 1993-94 Infiniti J30
1993.5 Infiniti G20
1994 Infiniti Q45
Classification: EL93-015
Section: Electrical
Bulletin No.: ITB93-068
Date: December 16, 1993
SERVICE INFORMATION
The proper procedure for programing additional remote controllers is listed below.
SERVICE PROCEDURE
While sitting inside the vehicle:
(1) Open the trunk.
(2) Close and lock all doors.
(3) Insert and remove the key from the ignition six times within 10 seconds.
(4) Manually unlock and lock driver's door once to enable "Belting" mode.
(5) Push lock button on the new remote controller once, just long enough to hear within 5 seconds of completing step 4.
(6) If additional remotes are needed (up to 3), repeat steps 4 and 5 for each additional remote immediately after programming the first remote.
NOTE: a total of four (4) remotes can be programmed to function on the same vehicle.
For additional information, please refer to page BF-38 of the 1993 and 1994 J30 Service Manuals: page BF-17 of the 1993 G20 Service Manual Supplement; and page EL-148 of the 1994 Q45 Service Manual.
:)
thanks will give it a try
J30/G20/Q45 REMOTE TRANSMITTER PROGRAMING
Model(s): 1993-94 Infiniti J30
1993.5 Infiniti G20
1994 Infiniti Q45
Classification: EL93-015
Section: Electrical
Bulletin No.: ITB93-068
Date: December 16, 1993
SERVICE INFORMATION
The proper procedure for programing additional remote controllers is listed below.
SERVICE PROCEDURE
While sitting inside the vehicle:
(1) Open the trunk.
(2) Close and lock all doors.
(3) Insert and remove the key from the ignition six times within 10 seconds.
(4) Manually unlock and lock driver's door once to enable "Belting" mode.
(5) Push lock button on the new remote controller once, just long enough to hear within 5 seconds of completing step 4.
(6) If additional remotes are needed (up to 3), repeat steps 4 and 5 for each additional remote immediately after programming the first remote.
NOTE: a total of four (4) remotes can be programmed to function on the same vehicle.
For additional information, please refer to page BF-38 of the 1993 and 1994 J30 Service Manuals: page BF-17 of the 1993 G20 Service Manual Supplement; and page EL-148 of the 1994 Q45 Service Manual.
:)
thanks will give it a try
Automotive Network, Inc., Copyright ©2026