turn signals all out ?

hello all! i have an emergency all my turn signals are out! i checked fuses all ok ? my hazzard lights work though! eh boy! any suggestions ? figures it is saturday night UGGHH!

99.9% positive it the Flasher. Go out anyway dude. use your hazards or hand signals yeah! I drove around for 2 months w/ mine out.

94-97 flashers were located behind your lighter sockets, inside the dash. And im not sure about 98+ or any thing prior. Best way to find it. Your hazards and signal flashers are next to eachother, well best case senario. turn on your hazards and listen for the tick. Flasher is like 6 bucks at a parts store. have fun

hi Extreem1 flasher u say ? is it a 1 pc part ? can you descibe it is must be electrical i guess . if i don't get ot fixed this afternoon , then i have to drive my 97 supersport camaro in rain 4 the 1st time in it;s life eh boy!. Also, when i would turn on the turn signals while they worked it seemed like they had a little play in them and would kick on my bright lights for a 1 billionth of a second [ only noticeable at night] ok late and time for bed thanks so much if it is the flasher!

does your multi switch still engage and disengage when you go around a corner. If not then its a pain to fix that. But if it still engages when you go to flip on your signal and it kicks back out when your turn is complete then its probably the flasher. The flasher, unless its been replaced, is a small circular, shinny aluminum object. You pull it out w/ plyers or whatever you can get in there. there pretty well stuck in there so dont be afraid when it doesnt want to come out with ease. make sure you test your hazards. The one that controls your hazards will tick as normal and you can feel that one tick. pull the other one that doesnt!

http://s89705872.onlinehome.us/DSC00611

Thanks again Extreem BEING ! LAST I KNOW THE ENGAGER WORKED! LATELY I WOULD SHUT IT OFF MANUALY [ FIGURING I WOULD SAVE A FEW BLINKS ON THE BULBS , THUS NOT BURNING OUT AS OFTEN . GOD I HOPE MY I SEE MINE LIKE YOUR PIC WAS THERE A COVER OVER THEM?as for what yoiu asked when i put the turn sigs on now[ while they are unoperable] now ticking sound . ok time to go lok ! thanks Stiletto

thanks i think i found it sounds like the right side is the culprit! extreemmeasures [ YOU RULE! ]

ok so i go to local auto part store, they give me a square one . nope i say, then a round one but it is flat on the outside , where mine is hollow with a brass looking 1/4 inch round something with a flat side ? at the bottom eh boy! so if i pull the whole round thing out ' [ maybe it would look right ]? thanks Stiletto

The one i got was clear. I went to advance auto. its was like 6 bucks. as long as the prongs are the same it doesnt matter what type you put in. just get a quality one so you dont have to do it for a long time. i think mine was a three prong but im not for sure. just bring in your old one and tell them 2 match it up.

well one step back for me, went to chevy dealer they say flasher is a black plastic rectangler with lots of prongs so the round ones i saw aren't BUMMER! THEN CHEVY SAYS PROBABLY the multi switch . leave there come home and read in my manual the my shiny silver rounds things are aux power Damn! but i do hear the flasher for the hazzards there. either GM is CRAZY or extreem is right hmmm?

well one step back for me, went to chevy dealer they say flasher is a black plastic rectangler with lots of prongs so the round ones i saw aren't BUMMER! THEN CHEVY SAYS PROBABLY the multi switch . leave there come home and read in my manual the my shiny silver rounds things are aux power Damn! but i do hear the flasher for the hazzards there. either GM is CRAZY or extreem is right hmmm?

The multiswitch fried on mine (Bravada, but shouldn't be any different) a little over a year ago. I tried replacing the flasher first, but no luck. It is black, rectangular, hidden behind the glovebox, and costs about $12 at the dealer. Didn't work. Ended up replacing the multiswitch and problem went away. I think the part was somewhere around the $150 at Autozone. Lot better than the $300+ the dealer quoted.

Black rectangular electronic w/ 4 prongs should be a relay. Keep looking for the flasher. they look just like that pic above. Usually gm puts both flashers next to eachother, hazards and signals. Its the first thing to go out. go 2 advance and ask them for the flasher for your specific truck. The manuals suck, they dont tell you specific locations. Just gotta pull it all apart and figure it out. If it ends up being the multi switch, like he said go 2 the parts store the dealers price is gonna be alot higher.

Well, mine is a 99, and the flasher is a black unit, rectangular, with several prongs on it - don't remember how many. It's behind the glovebox. Perhaps they changed the location from earlier years. I thought the same thing when they gave me the part, but they were correct.

hmmm. well then i stand corrected. Anyone else had this problem that would like 2 help Stiletto out here?

hello cool yes mine is a 99 too! i heard it as extreem mentioned and showed a pic of [thanks bud]!extreem is extreemely coo! Find out those 2 circular silvers are my opti power sources. So bix did you take out the glove box help me if you can i can't see nothing around and still feel it where extreem told me.The hottie chick at chevy showed the pic on her pc.The close up didn't even show it she said it might be in the engine compartment or passengers , looks like she was right on the 2nd and extreemely easy on the eyes! umn umn good! Thanks Stiletto

HI bIVE ok i reread what you said. multi switch culptit mine still works the bright lights , windshield washers everthing cept the turn sigs are the multi's hard to replace when i think all they do kinda scares me thinking of doing myself but that's all i can afford my day job is barely enough and my adult bookstore is never going to get off the ground eh boy! Stiletto

It is behind the glovebox. Watch when you open your glovebox, it will rest on a black clip when open. If you push that clip up, the glove box will continue to open all the down, giving you access to the relay behind it.

If your multifunction switch died like mine did, first you'd have the smoke coming out from the steering column while driving down the highway at 75MPH, which would make you wonder what's going on. After the smoke cleared, I noticed that my tuen signals no longer worked, and there was a constant "tick tick tick" sound from the flasher can, even with the turn signal stalk in the center position.

I used the tick tick sound to find the flasher. As blazee mentioned, you'll see if once you've gotten the glovebox out. Hopefully you've got the mysterious click click sound to trace it down.

I went out and took some pics. This is the location of the flasher relay on 98+


http://www.image-hosting.ws/direct/1488.jpg

http://www.image-hosting.ws/direct/1489.jpg

thanks biv and blazee Giosh i wonder how we [ if old enough you are ] survived without pc's and technology. i think back to high school if someone told me there was going to be an internet and cameras pictures would end up on it .and there would be websites and forumns on your favorite things.I would have thought they were looney! BUT HEY! 1986 WAS A LONG TIME AGO! ANCHOR BAY HIGH 1986 STILETTO I SALUTE YOU ALL WHO HELPED ME ! i never saw nor smelled smoke so hopefully it is just the flasher which should be able to find tomorrow thanks ever so much! Stiletto

0hi well i changed the flasher as blazee's pic showed tridon ep 29 at advance auto and nada! it is my hazzerd flasher when i pulled it out so did my hazzards go out . do we know if the hazzard and turn sigs shares the one flasher or are there 2. 1 for each? ???? EH BOY! HAPPY MEMORIAL DAY! SAD TURN SIGNAL DAY ! STILETTO

That relay works the hazzards and the turn signals. It's looking more like the multi-function switch is the problem. Normally when they go out the relay keeps clicking all the time, this is the first case that I've seen where the turn sigs quit and the relay doesn't keep clicking, so I'm reluctant to advise you to replace it, because it is an expensive part and a job to put in. Maybe someone can tell you how to test it without pulling the column apart.

hi Blazee happy memorial day ! ok i guess but EH BOY!!! thanks i have a pretty nice mech hank at hanks auto clinton twp MIchigan see if he can check it take care and goodluck on getting up for work after a long weekend Sincerely, Stiletto