oh oh cracked head or not?
jgillis
02-21-2005, 04:02 PM
After inspecting the heads i noticed between #1 and #3 a very fine line
that can be just felt with your fingernail doesn't go all the way into the combustion chamber but stops just where it starts to dip doesn't show up in the chamber but shows up on other side in same line.I put a straight edge on it and it is as straight as an arrow.
The strange thing is on the other head is the exact same line between #4 and #6????.
Since i live in nowhere land i would have to ship it 400 miles to have it checked lol.
I poled the 4 local mechanic here 2 said they thought it was some kind of scratch or milling mark they would put it back on.2 said they wern't sure.I sure wish there were 5 mechanics here lol.
Any thoughts??
that can be just felt with your fingernail doesn't go all the way into the combustion chamber but stops just where it starts to dip doesn't show up in the chamber but shows up on other side in same line.I put a straight edge on it and it is as straight as an arrow.
The strange thing is on the other head is the exact same line between #4 and #6????.
Since i live in nowhere land i would have to ship it 400 miles to have it checked lol.
I poled the 4 local mechanic here 2 said they thought it was some kind of scratch or milling mark they would put it back on.2 said they wern't sure.I sure wish there were 5 mechanics here lol.
Any thoughts??
A. Souphound
02-21-2005, 06:09 PM
After inspecting the heads i noticed between #1 and #3 a very fine line
that can be just felt with your fingernail doesn't go all the way into the combustion chamber but stops just where it starts to dip doesn't show up in the chamber but shows up on other side in same line.I put a straight edge on it and it is as straight as an arrow.
The strange thing is on the other head is the exact same line between #4 and #6????.
Since i live in nowhere land i would have to ship it 400 miles to have it checked lol.
I poled the 4 local mechanic here 2 said they thought it was some kind of scratch or milling mark they would put it back on.2 said they wern't sure.I sure wish there were 5 mechanics here lol.
Any thoughts??
jgillis,
To determine if it is a tooling mark or a cracK: clean the area as good as you can and then pour rubbing alcohol on the area. If it's a crack it will be the last area to evaporate, and show up very well. (Poor man's NDT)
that can be just felt with your fingernail doesn't go all the way into the combustion chamber but stops just where it starts to dip doesn't show up in the chamber but shows up on other side in same line.I put a straight edge on it and it is as straight as an arrow.
The strange thing is on the other head is the exact same line between #4 and #6????.
Since i live in nowhere land i would have to ship it 400 miles to have it checked lol.
I poled the 4 local mechanic here 2 said they thought it was some kind of scratch or milling mark they would put it back on.2 said they wern't sure.I sure wish there were 5 mechanics here lol.
Any thoughts??
jgillis,
To determine if it is a tooling mark or a cracK: clean the area as good as you can and then pour rubbing alcohol on the area. If it's a crack it will be the last area to evaporate, and show up very well. (Poor man's NDT)
HERB FOLLIN
03-17-2005, 01:17 PM
jgillis,
To determine if it is a tooling mark or a cracK: clean the area as good as you can and then pour rubbing alcohol on the area. If it's a crack it will be the last area to evaporate, and show up very well. (Poor man's NDT)
ON YOUR OTHER MATTER,,,ABOUT YOUR TIMING,,,PICK UP THE DISTRIBUTOR AND LOOK UNDER THE BOTTOM AND POINT YOUR ROTOR TO THE CONTACT,,,NOT THE NUMBER 1 WIRE PLUG,,,HERB...
To determine if it is a tooling mark or a cracK: clean the area as good as you can and then pour rubbing alcohol on the area. If it's a crack it will be the last area to evaporate, and show up very well. (Poor man's NDT)
ON YOUR OTHER MATTER,,,ABOUT YOUR TIMING,,,PICK UP THE DISTRIBUTOR AND LOOK UNDER THE BOTTOM AND POINT YOUR ROTOR TO THE CONTACT,,,NOT THE NUMBER 1 WIRE PLUG,,,HERB...
HERB FOLLIN
03-17-2005, 01:19 PM
jgillis,
To determine if it is a tooling mark or a cracK: clean the area as good as you can and then pour rubbing alcohol on the area. If it's a crack it will be the last area to evaporate, and show up very well. (Poor man's NDT)
ON YOUR OTHER MATTER,,,ABOUT YOUR TIMING,,,PICK UP THE DISTRIBUTOR CAP AND LOOK UNDER THE BOTTOM AND POINT YOUR ROTOR TO THE CONTACT,,,NOT THE NUMBER 1 WIRE PLUG,,,HERB...
To determine if it is a tooling mark or a cracK: clean the area as good as you can and then pour rubbing alcohol on the area. If it's a crack it will be the last area to evaporate, and show up very well. (Poor man's NDT)
ON YOUR OTHER MATTER,,,ABOUT YOUR TIMING,,,PICK UP THE DISTRIBUTOR CAP AND LOOK UNDER THE BOTTOM AND POINT YOUR ROTOR TO THE CONTACT,,,NOT THE NUMBER 1 WIRE PLUG,,,HERB...
chigger_ns
03-17-2005, 03:19 PM
You can buy crack finder. It usually comes in 3 cans. A cleaner, A penetrant and a magnifier. A local shop may sell these. A company by the name of CROWN is the one I have used!!!. It works!
jgillis
03-17-2005, 03:34 PM
The van is on the road now and running fine.
A. Souphound
03-17-2005, 06:34 PM
The van is on the road now and running fine.
Thanks for the up-date, glad to hear the good news.
All the best,
Thanks for the up-date, glad to hear the good news.
All the best,
chigger_ns
03-18-2005, 02:32 PM
Good to hear.
Automotive Network, Inc., Copyright ©2025