keyless entry lost remote
gwreed
07-25-2004, 05:00 PM
Recently lost remote to keyless entry for 98 crv.
Can buy used one on e-bay for 15.00 compared to 100+ from dealer.
Can used ones be reprogramed for my crv ? Thks
Can buy used one on e-bay for 15.00 compared to 100+ from dealer.
Can used ones be reprogramed for my crv ? Thks
gunnmen01
07-25-2004, 08:55 PM
yes they can, as long as they are crv remotes,but its kinda hard to explain how.... buy them and take then into the dealer and let them explain how to program then...
gunnmen01
gunnmen01
lorunner
08-28-2004, 02:16 PM
here is the programming steps
1997–04 CR-V LX with dealer-installed keyless
entry system
1998–04 CR-V EX with factory-installed
keyless entry system
2000–01 CR-V SE with factory-installed
keyless entry system
2000–04 S2000 with factory-installed keyless
entry system
2002–04 CR-V with dealer-installed security
system
Programming the Transmitter
NOTES:
• The system accepts up to three transmitters. The
transmitter codes are stored in a stacking-type
memory. If a fourth transmitter code is programmed,
the code for the first transmitter is erased.
• Entering the programming mode cancels all learned
transmitter codes, so none of the previously
programmed transmitters will work. You must
reprogram all of the transmitters once you are in the
programming mode.
• You must complete each step within 4 seconds of
the previous step to keep the system from exiting the
programming mode. Program the transmitters within
10 seconds.
1. Turn the ignition switch to ON (II).
2. Press the “Lock” or “Unlock” button on one of the
transmitters. (An unprogrammed transmitter can be
used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the
same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the “Lock” or “Unlock” button on the same
transmitter. Make sure the power door locks cycle
to confirm that the system is in programming mode.
7. Within 10 seconds, press the “Lock” or “Unlock”
button on each transmitter. Make sure the power
door locks cycle after you press each transmitter
button to confirm that the system accepted the
transmitter’s code.
8. Turn the ignition switch to LOCK (0) to exit the
programming mode.
1997–04 CR-V LX with dealer-installed keyless
entry system
1998–04 CR-V EX with factory-installed
keyless entry system
2000–01 CR-V SE with factory-installed
keyless entry system
2000–04 S2000 with factory-installed keyless
entry system
2002–04 CR-V with dealer-installed security
system
Programming the Transmitter
NOTES:
• The system accepts up to three transmitters. The
transmitter codes are stored in a stacking-type
memory. If a fourth transmitter code is programmed,
the code for the first transmitter is erased.
• Entering the programming mode cancels all learned
transmitter codes, so none of the previously
programmed transmitters will work. You must
reprogram all of the transmitters once you are in the
programming mode.
• You must complete each step within 4 seconds of
the previous step to keep the system from exiting the
programming mode. Program the transmitters within
10 seconds.
1. Turn the ignition switch to ON (II).
2. Press the “Lock” or “Unlock” button on one of the
transmitters. (An unprogrammed transmitter can be
used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the
same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the “Lock” or “Unlock” button on the same
transmitter. Make sure the power door locks cycle
to confirm that the system is in programming mode.
7. Within 10 seconds, press the “Lock” or “Unlock”
button on each transmitter. Make sure the power
door locks cycle after you press each transmitter
button to confirm that the system accepted the
transmitter’s code.
8. Turn the ignition switch to LOCK (0) to exit the
programming mode.
Automotive Network, Inc., Copyright ©2026