Thinking ABout Putting D16 In?
blade34609
11-01-2003, 12:48 PM
Hi,
I am planning on getting a hatch right after christmas.
Anyways, I have a D16A16 Si engine out of a 90' CRX sitting in my garage. I bought to swap into my 4 door but never got around to doing it. Anyways, I really dont have the time to swap the engine into the car with school and work. If I was to buy the hatch how much do you think it would cost to get that engine installed by a shop?
I know they would have to MPFI but all the rest is just bolt in.
I know I will have to buy the PM6 ECU and injector resistor box to provide for them. I live in Florida near Tampa, do any of you know fo any good shops in central Florida that could do it for me?
Thanks
I am planning on getting a hatch right after christmas.
Anyways, I have a D16A16 Si engine out of a 90' CRX sitting in my garage. I bought to swap into my 4 door but never got around to doing it. Anyways, I really dont have the time to swap the engine into the car with school and work. If I was to buy the hatch how much do you think it would cost to get that engine installed by a shop?
I know they would have to MPFI but all the rest is just bolt in.
I know I will have to buy the PM6 ECU and injector resistor box to provide for them. I live in Florida near Tampa, do any of you know fo any good shops in central Florida that could do it for me?
Thanks
blade34609
11-01-2003, 01:19 PM
How much would it cost a shope to just do an MPFI conversion?
If I supplied dizzy, ecu, injector box, and manifold?
If I supplied dizzy, ecu, injector box, and manifold?
88hondaowner
11-01-2003, 02:42 PM
Hey I got a PM6 ecu for 55bucks shipped if your interested. Its the ecu you need to swap to MPFI. Let me know
fredthedragon
11-01-2003, 07:26 PM
i sujjest you swap over to mpfi first i believe that will half the difference between your engine's hp and the si's hp. your only getting a fiew extra horses i sujjest at least a zc engine, they are around the same price... i know a fiew good sights if your interested. such as the sight where honda dealers get their zc engines :boink:
jackacc
11-01-2003, 07:42 PM
Hi,
I live in Florida near Tampa, do any of you know fo any good shops in central Florida that could do it for me?
Thanks
Labor will probably cost you around 800 but I had to buy hubs, axles, ecu, and a whole bunch of other stuff (that the car needed anyway...MC...caliper seals...etc...) Wound up costing me alot more than I thought in the longrun...but the A6 should be alot easier than the y8 I put in so you may not have to spend as much as you think. I had mine installed at A&H Automotive in Delray Beach, FL.. They did an awesome job. Not sure about the Tampa area... I just called everyone I found in the yellow pages until I found a shop that did swaps.
I live in Florida near Tampa, do any of you know fo any good shops in central Florida that could do it for me?
Thanks
Labor will probably cost you around 800 but I had to buy hubs, axles, ecu, and a whole bunch of other stuff (that the car needed anyway...MC...caliper seals...etc...) Wound up costing me alot more than I thought in the longrun...but the A6 should be alot easier than the y8 I put in so you may not have to spend as much as you think. I had mine installed at A&H Automotive in Delray Beach, FL.. They did an awesome job. Not sure about the Tampa area... I just called everyone I found in the yellow pages until I found a shop that did swaps.
blade34609
11-01-2003, 08:18 PM
Yea, im convinced I will probably just do the MPFI swap.
Then when I save enough money I will get a ZC or B18 engine.
How much would a ZC engine run me for a shop to install?
Thanks
Then when I save enough money I will get a ZC or B18 engine.
How much would a ZC engine run me for a shop to install?
Thanks
fredthedragon
11-01-2003, 10:16 PM
here's a nice place to buy engines from. shipping is a bitch but prices are right.
http://www.nippon-motors.com/honda.htm
http://www.nippon-motors.com/honda.htm
Automotive Network, Inc., Copyright ©2026