2012 Honda RC213V Casey Stoner (Late season)
LU YEN WEN
10-22-2016, 08:39 AM
Hello, guys. This is my first WIP in the forum, I just completed the last machine ridden by beloved Casey Stoner, REPSOL Honda RC213V.
I used a TAMIYA kit as base, and combined with K'S WORKSHOP trankit. the trans kit need so modification since the tank cover and seat are different from the 2013 type.
First, I did the clutch. I use Top Studio clutch set for 2002 RC211V, and combined it with the RC213V plastic parts.
http://i.imgur.com/HBv5Rtc.jpg
Then, I started doing the cowlings.
I glued the front and side first, so I don't need the screw holes.
Also I puttied the place for side cowl little wings.
http://i.imgur.com/mc0lGPz.jpg
I changed the shape of tank cover and seat, to reproduce the Stoner's bike.
Though not 100% the same it's acceptable for me.
http://i.imgur.com/0PWoLwP.jpg
http://i.imgur.com/i8mBpGP.jpg
http://i.imgur.com/IVdRGex.jpg
I also cut out some molds on the resin swing arm. The chain adjuster are different, and I planned to use some PE parts and detail-up shafts.
http://i.imgur.com/fvsMGl7.jpg
the original position of on board camera is too high, need modifications, too
http://i.imgur.com/Jkj9LKI.jpg
The duct size on the side cowl also need modification.
http://i.imgur.com/kmEka6O.jpg
just like this
http://i.imgur.com/MoadOT3.jpg
I wanted to make movable chain, but there haven't been any products.
so I do it myself with RC211V sets, combined with some plastic parts from RC213V.
http://i.imgur.com/3GrTuoW.jpg
I used 0.4mm masking tape to do the heat stain.
http://i.imgur.com/jUlXH8B.jpg
The shape of Casey's wind shied is different from Marc's, so I heat pressed it.
http://i.imgur.com/XlduRiI.jpg
http://i.imgur.com/nDGlLa8.jpg
http://i.imgur.com/3oyPqiz.jpg
the result is acceptable.
http://i.imgur.com/vGn8UTc.jpg
http://i.imgur.com/JniJlTF.jpg
doing the Honda emblem using T2M logo stickers and MaxMotoModeling decals
but the red area is too big so I adjusted it. you can see it on final result.
http://i.imgur.com/eu84C0x.jpg
http://i.imgur.com/dEYkeM4.jpg
masking the tyres to do the soft tyre used by Casey in Phillip Island.
http://i.imgur.com/2ax3azW.jpg
http://i.imgur.com/UaIiNod.jpg
painted the REPSOL color with fluorescent orange and fluorescent red from MaxMotoModeling. and TAMIYA TS-53.
http://i.imgur.com/nI7T7OM.jpg
http://i.imgur.com/GSoaC15.jpg
http://i.imgur.com/Txv7bcl.jpg
Also I did some carbon decals and modified the shape of left ankle guard
http://i.imgur.com/AsER9Li.jpg
http://i.imgur.com/GRfmeov.jpg
http://i.imgur.com/s61B17Z.jpg
here's the final result:
http://i.imgur.com/Wm7V4gK.jpg
More photos in the Completed Project post! Thank you.
I used a TAMIYA kit as base, and combined with K'S WORKSHOP trankit. the trans kit need so modification since the tank cover and seat are different from the 2013 type.
First, I did the clutch. I use Top Studio clutch set for 2002 RC211V, and combined it with the RC213V plastic parts.
http://i.imgur.com/HBv5Rtc.jpg
Then, I started doing the cowlings.
I glued the front and side first, so I don't need the screw holes.
Also I puttied the place for side cowl little wings.
http://i.imgur.com/mc0lGPz.jpg
I changed the shape of tank cover and seat, to reproduce the Stoner's bike.
Though not 100% the same it's acceptable for me.
http://i.imgur.com/0PWoLwP.jpg
http://i.imgur.com/i8mBpGP.jpg
http://i.imgur.com/IVdRGex.jpg
I also cut out some molds on the resin swing arm. The chain adjuster are different, and I planned to use some PE parts and detail-up shafts.
http://i.imgur.com/fvsMGl7.jpg
the original position of on board camera is too high, need modifications, too
http://i.imgur.com/Jkj9LKI.jpg
The duct size on the side cowl also need modification.
http://i.imgur.com/kmEka6O.jpg
just like this
http://i.imgur.com/MoadOT3.jpg
I wanted to make movable chain, but there haven't been any products.
so I do it myself with RC211V sets, combined with some plastic parts from RC213V.
http://i.imgur.com/3GrTuoW.jpg
I used 0.4mm masking tape to do the heat stain.
http://i.imgur.com/jUlXH8B.jpg
The shape of Casey's wind shied is different from Marc's, so I heat pressed it.
http://i.imgur.com/XlduRiI.jpg
http://i.imgur.com/nDGlLa8.jpg
http://i.imgur.com/3oyPqiz.jpg
the result is acceptable.
http://i.imgur.com/vGn8UTc.jpg
http://i.imgur.com/JniJlTF.jpg
doing the Honda emblem using T2M logo stickers and MaxMotoModeling decals
but the red area is too big so I adjusted it. you can see it on final result.
http://i.imgur.com/eu84C0x.jpg
http://i.imgur.com/dEYkeM4.jpg
masking the tyres to do the soft tyre used by Casey in Phillip Island.
http://i.imgur.com/2ax3azW.jpg
http://i.imgur.com/UaIiNod.jpg
painted the REPSOL color with fluorescent orange and fluorescent red from MaxMotoModeling. and TAMIYA TS-53.
http://i.imgur.com/nI7T7OM.jpg
http://i.imgur.com/GSoaC15.jpg
http://i.imgur.com/Txv7bcl.jpg
Also I did some carbon decals and modified the shape of left ankle guard
http://i.imgur.com/AsER9Li.jpg
http://i.imgur.com/GRfmeov.jpg
http://i.imgur.com/s61B17Z.jpg
here's the final result:
http://i.imgur.com/Wm7V4gK.jpg
More photos in the Completed Project post! Thank you.
Lockheed
10-24-2016, 12:12 AM
Gj!!!!!!!
malscar
10-28-2016, 07:38 PM
Beautifully done. Love it!
kaisers_phoenix
10-29-2016, 05:42 AM
:eek2::eek2::eek2::eek2:
Very nice, thanks for sharing!
Very nice, thanks for sharing!
sportracer02
11-24-2016, 02:47 AM
really impressive!!
KOM660
11-24-2016, 02:24 PM
Very very good work!!
John18d
11-30-2016, 03:31 PM
Thank you very much LU for your first WIP
Good start but please next time more - pictures and descriptions of what you are doing.
Very good start though - THANKS
Cheers
John
Good start but please next time more - pictures and descriptions of what you are doing.
Very good start though - THANKS
Cheers
John
Automotive Network, Inc., Copyright ©2024