Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Engineering/Technical Ask technical questions about cars. Do you know how a car engine works? |
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
04-05-2020, 11:15 AM | #1 | |
AF Newbie
Join Date: Apr 2020
Location: Pumpkin Town
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Tell my why my idea to prevent mis-shifts won't work
It's too easy to blow a motor in seconds with a money-shift. I'm surprised there aren't a lot of aftermarket products that address the problem.
Wouldn't it be relatively cheap and easy to affix something around the shifter that would mechanically close any gate for a gear that would over-rev the engine? Couldn't a wire connection to the ECU allow it to perform that function automatically? Or manually, with a button on the shifter knob that closes the gates for all lower gears? What am I missing? |
|
04-05-2020, 09:15 PM | #2 | |
Your worst nightmare
Join Date: Oct 2004
Location: Smithfield, Pennsylvania
Posts: 6,058
Thanks: 40
Thanked 252 Times in 246 Posts
|
Re: Tell my why my idea to prevent mis-shifts won't work
I was going to type a nice long response but I'll just put it this way, if it were that simple it would have happened by now.
__________________
|
|
04-06-2020, 05:57 AM | #3 | |
Registered Offender
Join Date: Mar 2006
Location: Rural
Posts: 6,518
Thanks: 6
Thanked 341 Times in 336 Posts
|
Re: Tell my why my idea to prevent mis-shifts won't work
A rev-limiter is intended specifically for that purpose. They have been around longer than most of our members.
__________________
Permanent seat assignment on the Group W bench... Automotive Forums Survival Guide |
|
04-06-2020, 07:03 AM | #4 | |
SHO No Mo
Join Date: Jun 2004
Location: Cedar Rapids, Iowa
Posts: 10,951
Thanks: 100
Thanked 350 Times in 344 Posts
|
Re: Tell my why my idea to prevent mis-shifts won't work
I don't see how a rev-limiter will work with a manual transmission vehicle though which is directly connected to the crankshaft once the working clutch system is engaged.
While this is an over-simplification of a system that seems like it could work with a small tachometer monitoring processor, small servos could be mounted next to each gate that would rotate a bar 90 degrees after the engine speed is too high to safely allow that gear to be engaged. The bar could have a "fork" on the opposite side of the gate for mechanical stiffness. There would be one servo and "fork" for each gear gate other than high gear or maybe the two highest gears. This means either the servos would need to be really small or the gates would need to be spread really far apart. Gates far apart are generally not preferred for performance shifting, and if you're not performance shifting, you probably don't need the gate lock outs. I alternative thought about a sliding bar system and a single linear actuator that would just slide a single bar for the lower gates and a duplicate system that would slide a bar for the upper gates, which solves the issue of needing the gates to be spread apart, but replaces that with a need for a wide distance between the transmission tunnel and the driver's leg or seat to accommodate the fully released bars. Hmm, looking at the clock, I wonder if this is similar to the long response Stealthee wanted to avoid. -Rod |
|
04-06-2020, 01:40 PM | #5 | |
AF Enthusiast
|
Re: Tell my why my idea to prevent mis-shifts won't work
Simply practice the art of precision gear changing, much more rewarding and satisfying than having some electronic gadgetry take the skillout of it.
|
|
|
POST REPLY TO THIS THREAD |
|
|