Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Hummer (AM General) > General Discussion
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools Search this Thread
Old 12-29-2002, 04:28 PM   #1
jan christensen
AF Newbie
 
Join Date: Dec 2002
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
Wiring Help Needed

I HAVE A 94 HUMMER WAGON THAT DOES NOT CHANGE OUT OF FIRST GEAR. I KNOW IT IS AN ELECTRICAL PROBLEM RELATED WITH THE TRANSMISSION CONTROL MODULE. DOES ANYONE KNOW WHERE I CNA GET WIRING DIAGRAMS ON THIS RELATED ISSUE OR HAVE ANY IDEAS WHAT THE PROBLEM MIGHT BE. THE SPEEDO DOES NOT WORK EITHER. THANKS.....JAN.
jan christensen is offline   Reply With Quote
Old 01-11-2007, 08:13 PM   #2
USMILRET
AF Newbie
 
Join Date: Jan 2007
Location: churchville, Maryland
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Wiring Help Needed

You should have a 1/2 shift solenoid that either isn't getting signal up to it, doesn't work or the spool valve doesn't work. That's just for first gear. If all of the other gears work fine then the pressure control valve works fine.
PM me.
USMILRET is offline   Reply With Quote
Old 11-06-2008, 07:17 PM   #3
GenBiltstein
AF Newbie
 
Join Date: Nov 2008
Location: Belair, Maryland
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Wiring Help Needed

If you have the 4L80-E transmission and if you have a transmission problem. You have a stuck checkball at the 1-2 shifting solenoid or the shifting valve is sticking and not returning.
I will describe the operation to you.
The computer controls the first gear in this manner.
By controlling the ground switch in the computer. when the puter decides enough is enough and lets go to second then it opens that switch and denying power to the 1-2 shifting solenoid. When that happens the pressure bleeds off and the valve relaxes and into second gear you go.

Provided the ECU is reading everything correctly like engine load and rpm.
GenBiltstein is offline   Reply With Quote
Old 02-08-2010, 11:36 PM   #4
alpinto088
AF Newbie
 
Join Date: Aug 2009
Location: Austin, Texas
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Wiring Help Needed

which type of help you needed..??
==========
albert
used caravans
alpinto088 is offline   Reply With Quote
Old 03-24-2010, 01:51 AM   #5
david357
AF Newbie
 
Join Date: Mar 2010
Location: CHARLOTTE
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Wiring Help Needed

Do you want a wiring diagram to fix the problem yourself or some suggestion on how to fix it. Its not clear
david357 is offline   Reply With Quote
Old 03-24-2010, 07:11 AM   #6
GenBiltstein
AF Newbie
 
Join Date: Nov 2008
Location: Belair, Maryland
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Re: Wiring Help Needed

Most likely it is not the wiring. It could be soleniod related.

Disconnect the passthough connector at the transmission. At the transmission side there are pins E and A. test those for resistance. I believe the resistance should fall into 14 ohms. Definitely not over 20 ohms.

You can check for continuity as well.

If all seems to check out well then drop the pan.
Get two nine volt batteries. Soldier them in series with two leads. Test the two leads right on the solenoid. You should hear a clicking sound.

You can also conduct the very same test at the passthrough connector. If you hear the clicking sound then you are good.

Check all grounds with a multimeter. .1 ohms from terminal to ground. Everywhere you go to check a ground. If it is higher then remove that ground and clean it. Recheck. Battery ground. Block. Battery to chassis. I mean everywhere.
If in the event that everything is checking out then remove the soleniod. There is a pressure checking procedure that is not done so much nowadays. Replace it. A 3/8s star socket and a ratchet are the tools.
You might have a hanging valve that doesn't want to move after actuation of the 1-2 solenoid. That will be verified after replacement of the solenoid.
GenBiltstein is offline   Reply With Quote
 
Similar Threads
Thread Thread Starter Forum Replies Last Post
Need Spark Plugs and Wire help need. 02DenaliXL Yukon 3 06-22-2009 08:00 AM
Air Suspension Wiring Help Needed nitrus rush Problem Diagnosis 5 08-28-2008 08:34 AM
Pop Up Camper Wiring Help Needed WillScarletMacaw M Bodies 6 10-25-2004 11:15 PM
Trailer wiring help needed please Indyrider M Bodies 4 09-21-2004 07:18 PM
HX wiring... help needed 4GZChatch '92-'95 Civic | EL | Civic Hybrid | Civic GX NGV 0 06-15-2004 09:42 AM

Reply

POST REPLY TO THIS THREAD


Bookmarks
Go Back   Automotive Forums .com Car Chat > Hummer (AM General) > General Discussion

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 03:24 PM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts