Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
05-07-2003, 05:09 PM | #1 | |
AF Newbie
Join Date: Mar 2003
Posts: 28
Thanks: 0
Thanked 0 Times in 0 Posts
|
Reprogramming Keyless Entry
I have a 2000 Oldsmobile Silhouette, I need the instructions on how to program new remotes to it. Thanks
|
|
05-31-2003, 01:23 PM | #2 | |
AF Newbie
Join Date: May 2003
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
|
I have a 1999 Silo and found the answer to reprogram in another thread.
Look under Chevrolet>Nonspecific>Keyless Entry Info Check down the list for TIREBURNER. He has many listings but look for the reply to the same question as yours from a 2001 Pontiac Montana owner. It is a listing of the GM's 1999 how to reprogram keyless entry units. It will work for your 2000 Silo. Make sure you do all your units, working or not, at the same time or the working ones will be disabled when you program a new one. Good Luck |
|
07-14-2003, 08:44 PM | #3 | |
AF Newbie
Join Date: Jul 2003
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
|
99 silo
I tried this w/ no luck. I can't seem to get in to the programing mode.
when i am done trying my original one still works, any other suggestions? |
|
07-17-2003, 07:55 AM | #4 | |
AF Newbie
Join Date: Jul 2003
Location: St. Paul, Minnesota
Posts: 10
Thanks: 0
Thanked 0 Times in 0 Posts
|
I"m not sure if this will help or not but I stumbled across a similar thread in the GMC/Jimmy forum. There is a thread titled "remote reprogramming" you might want to read. Just a thought.
|
|
08-06-2003, 08:52 AM | #5 | |
AF Newbie
|
93 Olds Silo
Will these procedures work for a 93 remote entry? Or can anyone post the procedure for me?
Thanks |
|
01-22-2006, 09:05 PM | #6 | |
AF Newbie
Join Date: Jan 2006
Location: Brooklyn, New York
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Reprogramming Keyless Entry
I need the instructions for the 98 silo. If anyone has it please be so kind...
|
|
02-06-2006, 07:16 AM | #7 | |
Authorized Vendor
Join Date: Sep 2003
Location: Keyless Entry Remotes
Posts: 741
Thanks: 0
Thanked 8 Times in 8 Posts
|
Re: Reprogramming Keyless Entry
97-00 use these:
Important! Once the BCM enters program mode, all transmitters must be programmed at the same time. Any transmitters not learned at this time will be erased. 1) Remove the key from the ignition cylinder 2) Remove the BCM PRGRM fuse from the fuse panel 3) Close all the doors 4) Close the liftgate 5) Turn the ign lock cylinder to the ACC. position 6) Turn the ignition lock cylinder to OFF, and then back to ACC within 1 second 7) Open and close front passenger door A chime will be heard when the system enters the BCM programming mode IMPORTANT! After 7 seconds a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming. 8) Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds 9) Repeat the previous step on each additional transmitter to be programmed. 10) Remove the ignition key from the ignition cylinder 11) Install the BCM PRGRM fuse back into the fuse panel.
__________________
Replacement keyless entry remotes available here - up to 90% off - All makes/models from Acura-Volvo, 1988-present - http://www.OriginalKeyless.com |
|
02-06-2006, 07:43 PM | #8 | |
AF Newbie
Join Date: Jul 2003
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Reprogramming Keyless Entry
Step 6, should be changed from within one second to as FAST as humanly possible
This is what was preventing my reprogram |
|
02-06-2006, 07:47 PM | #9 | |
AF Newbie
Join Date: Jul 2003
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Reprogramming Keyless Entry
Otherwise it work fine for a 1999 Silo
|
|
12-30-2006, 02:18 PM | #10 | |
AF Newbie
Join Date: Dec 2006
Location: Mercedes
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Reprogramming Keyless Entry
I have a 2001 olds silhouette
can anyone confirm the process for re-programming a new remote. Thanks DS |
|
06-26-2007, 09:22 PM | #11 | |
AF Newbie
Join Date: Jun 2007
Location: Saskatoon
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: Reprogramming Keyless Entry
I am having trouble getting this to work. After step 6, i get one chime, then a pause, then another 8 chimes, a pause, then one chime, then a pause, then another 8 chimes, a pause and then it does the same again, for the third time. I then follow the rest of the steps, but to no avail. Can anyone help??
|
|
06-26-2007, 11:37 PM | #12 | ||
AF Moderator
Join Date: Jan 2005
Location: El Paso, Texas
Posts: 18,017
Thanks: 30
Thanked 53 Times in 41 Posts
|
Re: Reprogramming Keyless Entry
Quote:
Sorry but please check the date and do not resurrect old threads. Furthermore, this one has run it's course. Start a new thread addressing your issue. Thread closed.
__________________
'08 Pontiac Grand Prix GXP (Dark Slate Metallic) - LS4 5.3L V8 '02 Oldsmobile Alero GL2 - LA1 3400 V6 '99 Buick Regal LS - L36 Series II 3800 V6 '03 Honda CR250R MX - 2 Stroke 250cc '97 Pontiac Grand Prix GTP - L67 Series II 3800 V6 Supercharged (Sold) Timeslip 08/12/06 AF Community Guidelines |
||
|
POST REPLY TO THIS THREAD |
|
|