Search | Car Forums | Gallery | Articles | Helper | AF 350Z | IgorSushko.com | Corporate |
| Latest | 0 Rplys |
|
Show Printable Version | Email this Page | Subscribe to this Thread |
|
Thread Tools |
01-23-2008, 12:19 AM | #1 | |
AF Newbie
Join Date: Jan 2008
Location: Bartlett, Tennessee
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
'99 Ford Contour- Died while turning and will not start
Have a 1999, Ford Contour, 4 cyc.
When I was making a turn, the engine shut down and vehicle coasted to a stop. Could not restart. Would act like it wanted to start but would not turn over. Now, earlier that day, I replaced the A/C relay, in which the heat and air now work properly. Was it just a coincidence that the vehicle broke down or could I have done something??? I checked to ensure all the fuses and relays in box were in good under drivers side. I checked reset inertia switch. I hear fuel pump when I turn engine on and fuel pump stays on for a couple of seconds. I browsed for any loose wires under hood and pushed on all to make sure. Any ideas what best possible problems may be? thx....kg |
|
01-24-2008, 03:45 PM | #2 | |
AF Newbie
Thread starter
Join Date: Jan 2008
Location: Bartlett, Tennessee
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: '99 Ford Contour- Died while turning and will not start
update....replaced fuel filter.
check coil pack- got spark from plug cleaned spark plugs. tried spraying starting fuild in carb. pulled off timing belt cover but not sure what I'm looking for; The belt doesn't look torn and is on tight When trying to start car, the timing belt or nothing in the area turns. Is it supposed to turn when tring to turn car on. Also, when I start after sitting awhile, it will make a pop at the carb area and smoke a little. But after that, when starting again, it does not. Any ideas. Need help. thx.....kg |
|
02-05-2008, 04:31 PM | #3 | |
AF Newbie
Thread starter
Join Date: Jan 2008
Location: Bartlett, Tennessee
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: '99 Ford Contour- Died while turning and will not start
checked error codes and have error code P1383.
What does this mean I should look for? Timing belt and pulleys do not turn when I crank car. I tried to manually turn pulley to timing belt and will only turn about 3 inches. Should it turn manually? What else can I check for, as I'm still not sure what the problem is? thanks for any help.....kg |
|
02-05-2008, 07:35 PM | #4 | |
AF Ford Contour-Advisor
Join Date: Mar 2003
Posts: 1,815
Thanks: 0
Thanked 2 Times in 2 Posts
|
Re: '99 Ford Contour- Died while turning and will not start
Yes, your crankshaft and pulleys should all turn when trying to start the car.
Btw, in case you want to read on the P1383, heres a post I found on contour.org. http://www.contour.org/ubbthreads/sh...ue#Post1002871
__________________
"The CEG Nazi" www.contour.org 1996 Ford Contour SE - Sold 3.0L V6 and Arizona Dyno Chip Turbo Kit 364 whp, 410 wtq @ 16 psi and only 4,700 rpms. 1999 Tropic Green SVT Contour - Bone stock and MINT |
|
02-19-2008, 09:39 PM | #5 | |
AF Newbie
Thread starter
Join Date: Jan 2008
Location: Bartlett, Tennessee
Posts: 8
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: '99 Ford Contour- Died while turning and will not start
fyi....It was the timing belt.
Timing belt replaced and now runs fine. |
|
02-26-2008, 12:28 PM | #6 | ||
AF Enthusiast
|
Re: '99 Ford Contour- Died while turning and will not start
Quote:
__________________
'98 Contuor SE, 2.5 V6 Auto Silver '08 Altima 2.5S, Auto Super Black |
||
10-19-2008, 09:59 PM | #7 | |
AF Newbie
Join Date: Oct 2008
Location: Griffin, Georgia
Posts: 1
Thanks: 0
Thanked 0 Times in 0 Posts
|
Re: '99 Ford Contour- Died while turning and will not start
Just don't make any more turns, and you should be fine.
|
|
|
POST REPLY TO THIS THREAD |
|
|