Automotive Forums .com - the leading automotive community online! Automotive Forums .com - the leading automotive community online!
Automotive Forums .com - the leading automotive community online! 
-
Latest | 0 Rplys
Go Back   Automotive Forums .com Car Chat > Subaru > Legacy / Liberty / Baja
Reply Show Printable Version Show Printable Version | Email this Page Email this Page | Subscription Subscribe to this Thread
 
Thread Tools
Old 01-11-2012, 06:56 PM   #1
Termite1988
AF Newbie
 
Join Date: Jan 2012
Location: High View, West Virginia
Posts: 14
Thanks: 2
Thanked 0 Times in 0 Posts
Thumbs down Head Gasket?

I have a 1998 Legacy 2.2L and need to replace the head gasket. I am contemplating replacing it myself or paying to have it done since I'm in graduate school. If anyone knows roughly how long I should expect to spend on replacing it and a ballpark figure on what a shop would charge (Chesapeake VA area) would be greatly appreciated.

Thanks- Termite
Termite1988 is offline   Reply With Quote
Old 01-12-2012, 02:56 PM   #2
rodeo02
AF Enthusiast
 
Join Date: Mar 2003
Location: Buffalo, New York
Posts: 3,213
Thanks: 0
Thanked 4 Times in 4 Posts
Re: Head Gasket?

I know my brother replaced the HG's on his 1998 himself. He borrowed an engine hoist, pulled and disassembled the engine himself, then had the cylinder heads checked/machined at a shop. By the time you replace gaskets, seals, belts, etc, you're probably looking at $600+ plus MANY hours of DIY work.

This wasn't an issue for him since this was his project car at the time.

This is probably a $1200 job to have a shop do it properly. I know that's the route I'd go if this was my daily-driver.

Joel
__________________
2016 Subaru Forester 2.5i base CVT
2016 Nissan Quest SV
rodeo02 is offline   Reply With Quote
The Following User Says Thank You to rodeo02 For This Useful Post:
Termite1988 (01-12-2012)
Old 01-12-2012, 03:04 PM   #3
Termite1988
AF Newbie
Thread starter
 
Join Date: Jan 2012
Location: High View, West Virginia
Posts: 14
Thanks: 2
Thanked 0 Times in 0 Posts
Re: Head Gasket?

Quote:
Originally Posted by rodeo02 View Post
I know my brother replaced the HG's on his 1998 himself. He borrowed an engine hoist, pulled and disassembled the engine himself, then had the cylinder heads checked/machined at a shop. By the time you replace gaskets, seals, belts, etc, you're probably looking at $600+ plus MANY hours of DIY work.

This wasn't an issue for him since this was his project car at the time.

This is probably a $1200 job to have a shop do it properly. I know that's the route I'd go if this was my daily-driver.

Joel
Thank you Joel,

I was given an estimate of ~1700.00 from the shop this morning that I had it carried to. Was looking for someone's opinion or insight as to what to expect. The est. included timing belt, head bolts, water pump, and the milling of the heads.

I'm not having an issue of tools and willingness, its the time to get back to my parents to undertake it. I reckon I'll bite the bullet and pay them to take care of it.

Thanks again for the reply.

Ben
Termite1988 is offline   Reply With Quote
Old 01-12-2012, 08:51 PM   #4
rodeo02
AF Enthusiast
 
Join Date: Mar 2003
Location: Buffalo, New York
Posts: 3,213
Thanks: 0
Thanked 4 Times in 4 Posts
Re: Head Gasket?

That's a painful bill for sure, but figure for $1700, pretty much everything you'd ever have to touch on the engine will have been replaced.

If the body and trans are in good shape, it's worth it.

Joel
__________________
2016 Subaru Forester 2.5i base CVT
2016 Nissan Quest SV
rodeo02 is offline   Reply With Quote
Old 01-12-2012, 09:04 PM   #5
Termite1988
AF Newbie
Thread starter
 
Join Date: Jan 2012
Location: High View, West Virginia
Posts: 14
Thanks: 2
Thanked 0 Times in 0 Posts
Re: Head Gasket?

I called them and told them to go ahead and take get started on it. It seems to be in good shape otherwise. Not the cleanest as far as interior goes but decent enough for my standards. The whole ~10.5 mpg in my truck has got to end sometime. Now just to hope trans. holds out for a few years.

Ben
Termite1988 is offline   Reply With Quote
 
Similar Threads
Thread Thread Starter Forum Replies Last Post
96 Altima : Trouble Starting After Head Gasket Replacement EliteDistance Altima 15 05-31-2010 03:56 AM
Head gasket or intake gasket? shayes5 Montana/Montana SV6 5 12-29-2009 10:42 AM
01 grand am 3400 head gasket? LoMbArD Grand AM 33 10-19-2009 12:29 PM
Head Gasket Leak or LIM Gasket? Bozly Monte Carlo 4 01-18-2009 05:44 PM
Intake gasket leak or head gasket vfour65 Impala | Impala SS 9 09-02-2008 07:37 PM

Reply

POST REPLY TO THIS THREAD

Go Back   Automotive Forums .com Car Chat > Subaru > Legacy / Liberty / Baja

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 10:00 AM.

Community Participation Guidelines | How to use your User Control Panel

Powered by: vBulletin | Copyright Jelsoft Enterprises Ltd.
 
 
no new posts